View WM8750LEFLR_22175.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

WM8750L
Stereo CODEC for Portable Audio Applications
DESCRIPTION
The WM8750L is a low power, high quality stereo codec designed for portable digital audio applications. The device integrates complete interfaces to stereo or mono microphones and a stereo headphone. External component requirements are drastically reduced as no separate microphone or headphone amplifiers are required. Advanced on-chip digital signal processing performs graphic equaliser, 3-D sound enhancement and automatic level control for the microphone or line input. The WM8750L can operate as a master or a slave, with various master clock frequencies including 12 or 24MHz for USB devices, or standard 256fs rates like 12.288MHz and 24.576MHz. Different audio sample rates such as 96kHz, 48kHz, 44.1kHz are generated directly from the master clock without the need for an external PLL. The WM8750L operates at supply voltages down to 1.8V, although the digital core can operate at voltages down to 1.42V to save power, and the maximum for all supplies is 3.6 Volts. Different sections of the chip can also be powered down under software control. The WM8750L is supplied in a very small and thin 5x5mm QFN package, ideal for use in hand-held and portable systems.
FEATURES
* * * * * DAC SNR 98dB (`A' weighted), THD -95B at 48kHz, 3.3V ADC SNR 95dB (`A' weighted), THD -90dB at 48kHz, 3.3V Complete Stereo / Mono Microphone Interface - Programmable ALC / Noise Gate On-chip 400mW BTL Speaker Driver (mono) On-chip Headphone Driver - >40mW output power on 16 / 3.3V - THD -80dB at 20mW, SNR 90dB with 16 load - No DC blocking capacitors required (capless mode) Separately mixed mono output Digital Graphic Equaliser Low Power - 7mW stereo playback (1.8V / 1.5V supplies) - 14mW record & playback (1.8V / 1.5V supplies) Low Supply Voltages - Analogue 1.8V to 3.6V - Digital core: 1.42V to 3.6V - Digital I/O: 1.8V to 3.6V 256fs / 384fs or USB master clock rates: 12MHz, 24MHz Audio sample rates: 8, 11.025, 16, 22.05, 24, 32, 44.1, 48, 88.2, 96kHz generated internally from master clock 5x5x0.9mm QFN package
* * * *
* * *
APPLICATIONS
* * * * MP3 Player / Recorder AAC/WMA/Multi-Format Player / Recorder Minidisc Player / Recorder Portable Digital Music Systems
BLOCK DIAGRAM
DGND
M U X
LMIXSEL
DC MEASUREMENT
LINPUT1 LINPUT2 LINPUT3
M U X LINSEL DIFF. INPUT L1-R1 OR L2-R2 RINSEL
PGA + MIC BOOST
ADC
DIGITAL FILTERS
A
WM8750L
AUDIO INTERFACE BCLK ADCLRC ADCDAT DACLRC DACDAT
DCVDD
DBVDD
HPGND
HPVDD
OUT3SW VREF ROUT1 LEFT LD2LO MIXER MONOOUT LI2LO
M U X
-1
OUT3
LOUT1
RD2LO
DAC
MONO LD2MO MIXER
RI2LO LI2MO
LOUT1VOL
DIGITAL FILTERS GRAPHIC EQUALISER BASS BOOST
VOLUME ANALOGUE MONO MIX DIGITAL MONO MIX
MONOOUT (phone TX)
RD2MO RI2MO LI2RO MONOVOL
RINPUT3/ HPDETECT RINPUT2 RINPUT1
M U X
PGA + MIC BOOST
ADC
3D ENHANCE
DAC
RIGHT LD2RO MIXER
ROUT1
RD2RO RI2RO ROUT1VOL
DC MEASUREMENT
M U X
RMIXSEL LOUT2VOL
LOUT2 L - (-R) = L+R ROUT2
ROUT2VOL
MICBIAS
50K 50K
-1
CLOCK CIRCUITRY
CONTROL INTERFACE
ROUT2 INV
AGND
VREF
MODE SCLK SDIN CSB
MCLK
AVDD
VMID
WOLFSON MICROELECTRONICS plc www.wolfsonmicro.com
Product Preview, May 2003, Rev 1.77
Copyright 2003 Wolfson Microelectronics plc
WM8750L TABLE OF CONTENTS
Product Preview
DESCRIPTION ......................................................................................................1 FEATURES ...........................................................................................................1 APPLICATIONS ....................................................................................................1 BLOCK DIAGRAM................................................................................................1 PIN CONFIGURATION .........................................................................................4 ORDERING INFORMATION .................................................................................4 PIN DESCRIPTION ...............................................................................................4 ABSOLUTE MAXIMUM RATINGS........................................................................5 RECOMMENDED OPERATION CONDITIONS ....................................................5 ELECTRICAL CHARACTERISTICS .....................................................................6
HEADPHONE / SPEAKER OUTPUT THD VERSUS POWER......................................8
POWER CONSUMPTION ...................................................................................11 SIGNAL TIMING REQUIREMENTS....................................................................12
SYSTEM CLOCK TIMING ..........................................................................................12 AUDIO INTERFACE TIMING - MASTER MODE........................................................12 AUDIO INTERFACE TIMING - SLAVE MODE ...........................................................13
DEVICE DESCRIPTION......................................................................................16
INTRODUCTION ........................................................................................................16 INPUT SIGNAL PATH ................................................................................................16 AUTOMATIC LEVEL CONTROL (ALC) ......................................................................22 3D STEREO ENHANCEMENT ...................................................................................25 OUTPUT SIGNAL PATH.............................................................................................26 ANALOGUE OUTPUTS ..............................................................................................31 ENABLING THE OUTPUTS........................................................................................33 HEADPHONE SWITCH ..............................................................................................33 THERMAL SHUTDOWN.............................................................................................35 HEADPHONE OUTPUT..............................................................................................35 DIGITAL AUDIO INTERFACE ....................................................................................36
PP Rev 1.77 May 2003 2
Product Preview
WM8750L
AUDIO INTERFACE CONTROL .................................................................................39 MASTER CLOCK AND AUDIO SAMPLE RATES .......................................................40 CONTROL INTERFACE .............................................................................................42 POWER SUPPLIES....................................................................................................43 POWER MANAGEMENT............................................................................................44
REGISTER MAP .................................................................................................46 DIGITAL FILTER CHARACTERISTICS..............................................................47
TERMINOLOGY .........................................................................................................47
DAC FILTER RESPONSES ................................................................................48 ADC FILTER RESPONSES ................................................................................49 DE-EMPHASIS FILTER RESPONSES ...............................................................50 HIGHPASS FILTER ............................................................................................51 APPLICATIONS INFORMATION ........................................................................52
RECOMMENDED EXTERNAL COMPONENTS .........................................................52 LINE INPUT CONFIGURATION .................................................................................53 MICROPHONE INPUT CONFIGURATION .................................................................53 MINIMISING POP NOISE AT THE ANALOGUE OUTPUTS .......................................54 POWER MANAGEMENT EXAMPLES........................................................................54
PACKAGE DIMENSIONS ...................................................................................55 IMPORTANT NOTICE........................................................................................ 54
ADDRESS: .................................................................................................................56
PP Rev 1.77 May 2003 3
WM8750L PIN CONFIGURATION
RINPUT3 / HPDETECT
Product Preview
ORDERING INFORMATION
ORDER CODE WM8750LEFL
16 15 14 13 12 11 10 9
LINPUT3
MICBIAS
HPVDD
AGND
AVDD
VREF
VMID
TEMPERATURE RANGE -25C to +85C
PACKAGE 32-pin QFN (5x5x0.9mm) 32-pin QFN (5x5x0.9mm) (lead free) 32-pin QFN (5x5x0.9mm) (tape and reel) 32-pin QFN (5x5x0.9mm) (lead free, tape and reel)
24
23
22
21
20
19
18
17
RINPUT2 25 LINPUT2 26 RINPUT1 27 LINPUT1 28 MODE 29 CSB 30 SDIN 31 SCLK 32
1 2 3 4 5 6 7 8
LOUT2 ROUT2 HPGND LOUT1 ROUT1 OUT3 MONOOUT ADCLRC
WM8750LSEFL
-25C to +85C
WM8750LEFL/R
-25C to +85C
WM8750LSEFL/R
-25C to +85C
DACDAT
DACLRC
ADCDAT
DCVDD
DBVDD
DGND
MCLK
BCLK
Note: Reel quantity = 3500
PIN DESCRIPTION
PIN # 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 NAME MCLK DCVDD DBVDD DGND BCLK DACDAT DACLRC ADCDAT ADCLRC MONOOUT OUT3 ROUT1 LOUT1 HPGND ROUT2 LOUT2 HPVDD AVDD AGND VREF VMID MICBIAS RINPUT3 / HPDETECT LINPUT3 RINPUT2 LINPUT2 RINPUT1 LINPUT1 MODE CSB SDIN SCLK Supply Supply Supply Digital Input / Output Digital Input Digital Input / Output Digital Output Digital Input / Output Analogue Output Analogue Output Analogue Output Analogue Output Supply Analogue Output Analogue Output Supply Supply Supply Analogue Output Analogue Output Analogue Output Analogue Input Analogue Input Analogue Input Analogue Input Analogue Input Analogue Input Digital Input Digital Input Digital Input/Output Digital Input TYPE Digital Input Master Clock Digital Core Supply Digital Buffer (I/O) Supply Digital Ground (return path for both DCVDD and DBVDD) Audio Interface Bit Clock DAC Digital Audio Data Audio Interface Left / Right Clock/Clock Out ADC Digital Audio Data Audio Interface Left / Right Clock Mono Output Analogue Output 3 (can be used as Headphone Pseudo Ground) Right Output 1 (Line or Headphone) Left Output 1 (Line or Headphone) Supply for Analogue Output Drivers (LOUT1/2, ROUT1/2) Right Output 1 (Line or Headphone or Speaker) Left Output 1 (Line or Headphone or Speaker) Supply for Analogue Output Drivers (LOUT1/2, ROUT1/2, MONOUT) Analogue Supply Analogue Ground (return path for both AVDD and MVDD) Reference Voltage Decoupling Capacitor Midrail Voltage Decoupling Capacitor Microphone Bias Right Channel Input 3 or Headphone Plug-in Detection Left Channel Input 3 Right Channel Input 2 Left Channel Input 2 Right Channel Input 1 Left Channel Input 1 Control Interface Selection Chip Select / Device Address Selection Control Interface Data Input / 2-wire Acknowledge output Control Interface Clock Input PP Rev 1.77 May 2003 4 DESCRIPTION
Product Preview
WM8750L
ABSOLUTE MAXIMUM RATINGS
Absolute Maximum Ratings are stress ratings only. Permanent damage to the device may be caused by continuously operating at or beyond these limits. Device functional operating limits and guaranteed performance specifications are given under Electrical Characteristics at the test conditions specified.
ESD Sensitive Device. This device is manufactured on a CMOS process. It is therefore generically susceptible to damage from excessive static voltages. Proper ESD precautions must be taken during handling and storage of this device. The WM8750L has been classified as MSL1, which has an unlimited floor life at <30 C / 85% Relative Humidity and therefore will not be supplied in moisture barrier bags. CONDITION Supply voltages Voltage range digital inputs Voltage range analogue inputs Operating temperature range, TA Storage temperature prior to soldering Storage temperature after soldering Package body temperature (soldering 10 seconds) Package body temperature (soldering 2 minutes) Notes 1. 2. 3. Analogue and digital grounds must always be within 0.3V of each other. All digital and analogue supplies are completely independent from each other. DCVDD must be less than or equal to AVDD & DBVDD. MIN -0.3V DGND -0.3V AGND -0.3V -25C -65C MAX +3.63V DBVDD +0.3V AVDD +0.3V +85C +150C +260C +183C
o
30C max / 85% RH max
RECOMMENDED OPERATION CONDITIONS
PARAMETER Digital supply range (Core) Digital supply range (Buffer) Analogue supplies range Ground SYMBOL DCVDD DBVDD AVDD, HPVDD DGND,AGND, HPGND MIN 1.42 1.8 1.8 TYP 2.0 2.0 2.0 0 MAX 3.6 3.6 3.6 UNIT V V V V
PP Rev 1.77 May 2003 5
WM8750L ELECTRICAL CHARACTERISTICS
Product Preview
Test Conditions o DCVDD = 1.5V, DBVDD = 3.3V, AVDD = HPVDD = 3.3V, TA = +25 C, 1kHz signal, fs = 48kHz, PGA gain = 0dB, 24-bit audio data unless otherwise stated. PARAMETER Full Scale Input Signal Level (for ADC 0dB Input at 0dB Gain) Input Resistance SYMBOL VINFS TEST CONDITIONS AVDD = 3.3V AVDD = 1.8V Selected for ADC, PGA gain = 0dB Selected for ADC, PGA gain = +30dB Selected for mixer Input unused Input Capacitance Signal to Noise Ratio (A-weighted) Dynamic Range Total Harmonic Distortion THD SNR AVDD = 3.3V AVDD = 1.8V -60dBFs -0.5dBFs input, AVDD = 3.3V -0.5dBFs input, AVDD = 1.8V ADC Channel Separation Channel Matching Programmable Gain Amplifier (PGA) Programmable Gain Programmable Gain Step Size Channel Matching Automatic Level Control (ALC) Target Record Level Gain Hold Time Gain Ramp-Up (Decay) Time Gain Ramp-Down (Attack) Time tHLD MCLK = 12.288MHz tDCY tATK -28.5 -6 dBFS ms ms ms 0, 2.67, 5.33, 10.67, ... , 43691 (time doubles with each step) 24, 48, 96, ... , 2458 (time doubles with each step) 6, 12, 24, ... , 6140 (time doubles with each step) AVDD=3.3V AVDD=1.8V THD AVDD=3.3V AVDD=1.8V Channel Separation Analogue Outputs (LOUT1/2, ROUT1/2, MONOOUT) 0dB Full scale output voltage Programmable Gain Programmable Gain Steps Mute attenuation Channel Separation 1kHz signal Monotonic 1kHz, full scale signal 80 -67 80 85 90 AVDD/3.3 +6 Vrms dB steps dB dB 1kHz signal TBD 98 95 -95 -90 90 dB dB Monotonic 1kHz signal, 0dB Fs input -17.25 0.5 0.75 0.2 30 1.0 dB dB dB 1kHz signal 1kHz signal 90 90 12 1 MIN TYP 1.0 0.545 20 1.5 TBD TBD 10 95 90 95 -90 0.003 -84 0.006 85 0.2 -84 0.006 -74 0.02 dB dB dB dB % pF dB k MAX UNIT V rms
Analogue Inputs (LINPUT1, RINPUT1, LINPUT2, RINPUT2, LINPUT3, RINPUT3) to ADC out
DAC to Line-Out (L/ROUT2 with 10k: / 50pF load) Signal to Noise Ratio (A-weighted) Total Harmonic Distortion SNR dB
PP Rev 1.77 May 2003 6
Product Preview
WM8750L
Test Conditions o DCVDD = 1.5V, DBVDD = 3.3V, AVDD = HPVDD = 3.3V, TA = +25 C, 1kHz signal, fs = 48kHz, PGA gain = 0dB, 24-bit audio data unless otherwise stated. PARAMETER Output Power per channel Total Harmonic Distortion SYMBOL PO THD TEST CONDITIONS MIN TYP MAX UNIT
Headphone Output (LOUT1/ROUT1, using capacitors) Output power is very closely correlated with THD; see below. HPVDD=1.8V, RL=32 PO=5mW HPVDD=1.8V, RL=16 PO=5mW HPVDD=3.3V, RL=32, PO=20mW HPVDD=3.3V, RL=16, PO=20mW Signal to Noise Ratio (A-weighted) Output Power Total Harmonic Distortion SNR HPVDD = 3.3V HPVDD = 1.8V PO THD 0.013 -78 0.013 -78 0.01 -80 0.01 -80 90 90 dB % dB
Speaker Output (LOUT2/ROUT2 with 8: bridge tied load, ROUT2INV=1) Output power is very closely correlated with THD; see below. Po=180mW, RL=8, HPVDD=3.3V Po=400mW, RL=8 HPVDD=3.3V Signal to Noise Ratio (A-weighted) Analogue Reference Levels Midrail Reference Voltage Potential Divider Resistance Buffered Reference Voltage Microphone Bias Bias Voltage Bias Current Source Output Noise Voltage Digital Input / Output Input HIGH Level Input LOW Level Output HIGH Level Output LOW Level HPDETECT (pin 23) Input HIGH Level Input LOW Level VIH VIL 0.7xAVDD 0.3xAVDD V V VIH VIL VOH VOL IOL=1mA IOH-1mA 0.9xDBVDD 0.1xDBVDD 0.7xDBVDD 0.3xDBVDD V V V V VMICBIAS IMICBIAS Vn 1K to 20kHz 15 -3% 0.9xAVDD + 3% 3 V mA nV/Hz VMID RVMID VREF -3% -3% AVDD/2 50 AVDD/2 +3% +3% V k V SNR HPVDD=3.3V, RL=8 HPVDD=2.5V, RL=8 -50 0.3 -40 1 90 90 dB dB %
PP Rev 1.77 May 2003 7
WM8750L
OUTPUT PGA'S LINEARITY
Product Preview
10.000 0.000 Output PGA Gains -10.000 Measured Gain [dB] -20.000 -30.000 -40.000 -50.000 -60.000 -70.000 40 50 60 70 80 90 100 110 120 130 XXXVOL Register Setting (binary) LOUT1 ROUT1 LOUT2 ROUT2 MONOOUT
2.000 1.750 Output PGA Gain Step Size 1.500 1.250 1.000 0.750 LOUT1 0.500 0.250 0.000 40 50 60 70 80 90 100 110 120 130 ROUT1 LOUT2 ROUT2 MONOOUT
Step Size [dB]
XXXVOL Register Setting (binary)
PP Rev 1.77 May 2003 8
Product Preview
WM8750L
HEADPHONE OUTPUT THD VERSUS POWER
0 Headphone Pow er vs THD+N (32Ohm load) -20
THD+N (dB)
-40
AVDD=1.8V AVDD=1.8V, capless AVDD=3.3V
-60
AVDD=3.3V, capless
-80
-100 0 5 10 15 Pow er (m W) 20 25 30
0 Headphone Pow er vs THD+N (16Ohm load) -20
THD+N (dB)
-40
AVDD=1.8V AVDD=1.8V, capless AVDD=3.3V
-60
AVDD=3.3V, capless
-80
-100 0 10 20 30 Pow er (m W) 40 50 60
PP Rev 1.77 May 2003 9
WM8750L
SPEAKER OUTPUT THD VERSUS POWER
Product Preview
-10 -20 -30 AVDD=1.8V -40 -50 -60 -70 0 100 200 300 400 500 Pow er (m W) Speaker Pow er vs THD+N (8Ohm BTL load) AVDD=2.5V AVDD=3.3V
THD+N (dB)
10 Speaker Power vs THD+N (8 Ohm BTL load) 8
THD+N (%)
6
AVDD=1.8V AVDD=2.5V AVDD=3.3V
4
2
0 0 100 200 300 400 500 Power (mW)
PP Rev 1.77 May 2003 10
Product Preview
WM8750L
POWER CONSUMPTION
The power consumption of the WM8750L depends on the following factors. * Supply voltages: Reducing the supply voltages also reduces supply currents, and therefore results in significant power savings, especially in the digital sections of the WM8750L. * Operating mode: Significant power savings can be achieved by always disabling parts of the WM8750L that are not used (e.g. mic pre-amps, unused outputs, DAC, ADC, etc.)
Control Register VMIDSEL Bit OFF R25 (19h) R26 (1Ah) R24 R23 VSEL Other settings AVDD DCVDD DBVDD HPVDD Tot. Power
V I (mA) V I (mA) V I (mA) V I (mA) 00 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 11 Clocks stopped 3.3 0.0016 3.3 0.0190 3.3 0.0080 3.3 0.0002 01 2.5 0.0008 2.5 0.0170 2.5 0.0050 2.5 0.0000 00 1.8 0.0005 1.5 0.0120 1.5 0.0029 1.8 0.0000 Standby 10 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 11 Interface Stopped 3.3 0.3900 3.3 0.0390 3.3 0.0080 3.3 0.0000 (500 KOhm VMID string) 01 2.5 0.2880 2.5 0.0170 2.5 0.0050 2.5 0.0000 00 1.8 0.1970 1.5 0.0120 1.5 0.0030 1.8 0.0000 Playback to Line-out 01 1 0 0 0 0 0 1 1 0 0 1 1 0 0 0 0 11 3.3 3.7310 3.3 5.6600 3.3 0.3000 3.3 0.2370 01 2.5 2.6940 2.5 3.8600 2.5 0.2200 2.5 0.2100 00 1.8 1.8820 1.5 2.1400 1.5 0.1240 1.8 0.1500 Playback to Line-out 01 1 0 0 0 0 0 1 1 1 1 0 0 0 0 0 1 11 3.3 3.5170 3.3 4.6470 3.3 0.3000 3.3 0.9500 (64x oversampling mode) 01 2.5 2.5760 2.5 3.2030 2.5 0.2200 2.5 0.6480 00 1.8 1.7760 1.5 1.7590 1.5 0.1240 1.8 0.4130 Playback to 16 Ohm Headphone 01 1 0 0 0 0 0 1 1 1 1 0 0 0 0 0 0 11 3.3 3.7260 3.3 5.6700 3.3 0.3000 3.3 0.9530 01 2.5 2.7530 2.5 3.9250 2.5 0.2200 2.5 0.6570 00 1.8 1.8900 1.5 2.1410 1.5 0.1240 1.8 0.4150 Playback to 16 Ohm Headphone 01 1 0 0 0 0 0 1 1 1 1 0 0 0 1 0 0 11 R24, OUT3SW=00 3.3 3.7060 3.3 5.6400 3.3 0.3000 3.3 1.4040 (capless mode using OUT3) 01 2.5 2.7130 2.5 3.9000 2.5 0.2200 2.5 0.9600 00 1.8 1.8870 1.5 2.1410 1.5 0.1240 1.8 0.6140 Playback to 8 Ohm BTL Speaker 01 1 0 0 0 0 0 1 1 0 0 1 1 0 0 0 0 11 R24, ROUT2INV=1 3.3 3.8820 3.3 5.6470 3.3 0.3000 3.3 0.2830 01 2.5 2.8780 2.5 3.9390 2.5 0.2200 2.5 0.2100 00 1.8 1.9800 1.5 2.1630 1.5 0.1240 1.8 0.1510 Headphone Amp 01 1 0 0 0 0 0 0 0 1 1 0 0 0 0 0 0 11 Clocks Stopped 3.3 1.8400 3.3 0.0200 3.3 0.0080 3.3 0.9540 (line-in to 16 Ohm headphone) 01 2.5 1.3300 2.5 0.0190 2.5 0.0050 2.5 0.6400 00 1.8 0.9300 1.5 0.0130 1.5 0.0030 1.8 0.4100 Speaker Amp 01 1 0 0 0 0 0 0 0 0 0 1 1 0 0 0 0 11 Clocks Stopped 3.3 1.9780 3.3 0.0200 3.3 0.0080 3.3 0.3310 (line-in to 8 Ohm speaker) 01 R24, ROUT2INV=1 2.5 1.4300 2.5 0.0190 2.5 0.0050 2.5 0.2430 00 1.8 0.9860 1.5 0.0130 1.5 0.0030 1.8 0.1760 Phone Call 01 1 0 0 0 0 1 0 0 0 0 1 1 1 0 0 0 11 Clocks Stopped 3.3 2.5230 3.3 0.0370 3.3 0.0080 3.3 0.4420 (mono line-in to headphone, 01 2.5 1.8520 2.5 0.0190 2.5 0.0050 2.5 0.3200 mic to MONOOUT) 00 1.8 1.2900 1.5 0.0130 1.5 0.0030 1.8 0.2240 Record from Line-in 01 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 11 3.3 8.6600 3.3 6.5700 3.3 0.3330 3.3 0.0000 01 2.5 7.7100 2.5 4.2800 2.5 0.2320 2.5 0.0000 00 1.8 6.8000 1.5 2.2100 1.5 0.1350 1.8 0.0000 Record from Line-in 01 1 1 1 1 1 0 0 0 0 0 0 0 0 0 1 0 11 3.3 5.0720 3.3 5.9100 3.3 0.3390 3.3 0.0000 (64x oversampling mode) 01 2.5 4.2550 2.5 3.7500 2.5 0.2320 2.5 0.0000 00 1.8 3.5900 1.5 1.9100 1.5 0.1350 1.8 0.0000 Record from mono microphone 01 1 1 0 1 0 1 0 0 0 0 0 0 0 0 0 0 11 R32, LMICBOOST=11; 3.3 4.9330 3.3 6.5400 3.3 0.3390 3.3 0.0000 01 R23, DATSEL=01 2.5 4.2970 2.5 4.2500 2.5 0.2400 2.5 0.0000 00 1.8 3.7210 1.5 2.2200 1.5 0.1370 1.8 0.0000 Record from mono microphone 01 1 1 0 1 0 1 0 0 0 0 0 0 0 0 0 0 11 R32, LMICBOOST=11; 3.3 5.2900 3.3 6.5000 3.3 0.3220 3.3 0.0000 (differential) 01 R23, DATSEL=01; 2.5 4.5600 2.5 4.2700 2.5 0.2400 2.5 0.0000 00 R32, LINSEL=11 1.8 3.9000 1.5 2.2200 1.5 0.1380 1.8 0.0000 Stereo Record & Playback 01 1 1 1 1 1 1 1 1 0 0 1 1 0 0 0 0 11 3.3 11.927 3.3 10.870 3.3 0.3320 3.3 0.2820 01 2.5 10.112 2.5 7.3600 2.5 0.2340 2.5 0.2060 00 1.8 7.3910 1.5 4.0610 1.5 0.1320 1.8 0.1480 Stereo Record & Playback 01 1 1 1 1 1 1 1 1 0 0 1 1 0 0 1 1 11 3.3 8.1090 3.3 9.3300 3.3 0.3330 3.3 0.2820 (64x oversampling mode) 01 2.5 6.5500 2.5 6.3020 2.5 0.2340 2.5 0.2070 00 1.8 4.7000 1.5 3.3800 1.5 0.1320 1.8 0.1490
VREF AINL AINR ADCL ADCR MICB DACL DACR LOUT1 ROUT1 LOUT2 ROUT2 MONO OUT3 ADCOSR DACOSR
mW 0.0950 0.0570 0.0233 1.4421 0.7750 0.3771 32.7624 17.4600 7.0536 31.0662 16.6175 6.7647 35.1417 18.8875 7.5465 36.4650 19.4825 7.8993 33.3696 18.1175 7.2663 9.3126 4.9850 2.4360 7.7121 4.2425 2.1156 9.9330 5.4900 2.7492 51.3579 30.5550 15.7575 37.3593 20.5925 9.5295 38.9796 21.9675 10.2333 39.9696 22.6750 10.5570 77.2563 44.7800 19.8597 59.5782 33.2325 13.9962
Table 1 Supply Current Consumption
Notes: 1. 2. All figures are at TA = +25 C, Slave Mode, fs = 48kHz, MCLK = 12.288 MHz (256fs), with zero signal (quiescent) The power dissipated in the headphone or speaker is not included in the above table.
o
PP Rev 1.77 May 2003 11
WM8750L SIGNAL TIMING REQUIREMENTS
SYSTEM CLOCK TIMING
tMCLKL MCLK tMCLKH tMCLKY
Product Preview
Figure 1 System Clock Timing Requirements Test Conditions CLKDIV2=0, DCVDD = 1.42V, DBVDD = 3.3V, DGND = 0V, TA = +25 C, Slave Mode fs = 48kHz, MCLK = 384fs, 24-bit data, unless otherwise stated. PARAMETER System Clock Timing Information MCLK System clock pulse width high MCLK System clock pulse width low MCLK System clock cycle time MCLK duty cycle Test Conditions CLKDIV2=1, DCVDD = 1.42V, DBVDD = 3.3V, DGND = 0V, TA = +25 C, Slave Mode fs = 48kHz, MCLK = 384fs, 24-bit data, unless otherwise stated. PARAMETER System Clock Timing Information MCLK System clock pulse width high MCLK System clock pulse width low MCLK System clock cycle time TMCLKL TMCLKH TMCLKY 10 10 27 ns ns ns SYMBOL MIN TYP MAX UNIT
o o
SYMBOL TMCLKL TMCLKH TMCLKY TMCLKDS
MIN 21 21 54 60:40
TYP
MAX
UNIT ns ns ns
40:60
AUDIO INTERFACE TIMING - MASTER MODE
BCLK (Output) ADCLRC/ DACLRC (Outputs) tDL
tDDA ADCDAT
DACDAT tDST tDHT
Figure 2 Digital Audio Data Timing - Master Mode (see Control Interface)
PP Rev 1.77 May 2003 12
Product Preview
WM8750L
Test Conditions DCVDD = 1.42V, DBVDD = 3.3V, DGND = 0V, TA = +25 C, Slave Mode, fs = 48kHz, MCLK = 256fs, 24-bit data, unless otherwise stated. PARAMETER Audio Data Input Timing Information ADCLRC/DACLRC propagation delay from BCLK falling edge ADCDAT propagation delay from BCLK falling edge DACDAT setup time to BCLK rising edge DACDAT hold time from BCLK rising edge tDL tDDA tDST tDHT 10 10 10 10 ns ns ns ns SYMBOL MIN TYP MAX UNIT
o
AUDIO INTERFACE TIMING - SLAVE MODE
tBCH BCLK tBCY DACLRC/ ADCLRC tDS DACDAT tDD ADCDAT tDH tLRH tLRSU tBCL
Figure 3 Digital Audio Data Timing - Slave Mode
Test Conditions DCVDD = 1.42V, DBVDD = 3.3V, DGND = 0V, TA = +25 C, Slave Mode, fs = 48kHz, MCLK = 256fs, 24-bit data, unless otherwise stated. PARAMETER SYMBOL MIN TYP MAX UNIT Audio Data Input Timing Information BCLK cycle time BCLK pulse width high BCLK pulse width low ADCLRC/DACLRC set-up time to BCLK rising edge ADCLRC/DACLRC hold time from BCLK rising edge DACDAT hold time from BCLK rising edge ADCDAT propagation delay from BCLK falling edge Note: BCLK period should always be greater than or equal to MCLK period. tBCY tBCH tBCL tLRSU tLRH tDH tDD 50 20 20 10 10 10 10 ns ns ns ns ns ns ns
o
PP Rev 1.77 May 2003 13
WM8750L
CONTROL INTERFACE TIMING - 3-WIRE MODE
tCSL CSB tCSS tSCL tSCS tCSH
Product Preview
tSCY tSCH SCLK
SDIN tDSU tDHO
LSB
Figure 4 Control Interface Timing - 3-Wire Serial Control Mode Test Conditions DCVDD = 1.42V, DBVDD = 3.3V, DGND = 0V, TA = +25 C, Slave Mode, fs = 48kHz, MCLK = 256fs, 24-bit data, unless otherwise stated. PARAMETER SYMBOL MIN TYP MAX UNIT Program Register Input Information SCLK rising edge to CSB rising edge SCLK pulse cycle time SCLK pulse width low SCLK pulse width high SDIN to SCLK set-up time SCLK to SDIN hold time CSB pulse width low CSB pulse width high CSB rising to SCLK rising Pulse width of spikes that will be suppressed tSCS tSCY tSCL tSCH tDSU tDHO tCSL tCSH tCSS tps 80 200 80 80 40 40 40 40 40 5 ns ns ns ns ns ns ns ns ns ns
o
PP Rev 1.77 May 2003 14
Product Preview
WM8750L
CONTROL INTERFACE TIMING - 2-WIRE MODE
t3 SDIN t4 t6 SCLK t1 t9 t7 t2 t8 t5 t3
Figure 5 Control Interface Timing - 2-Wire Serial Control Mode Test Conditions DCVDD = 1.42V, DBVDD = 3.3V, DGND = 0V, TA = +25 C, Slave Mode, fs = 48kHz, MCLK = 256fs, 24-bit data, unless otherwise stated. PARAMETER SYMBOL MIN TYP MAX UNIT Program Register Input Information SCLK Frequency SCLK Low Pulse-Width SCLK High Pulse-Width Hold Time (Start Condition) Setup Time (Start Condition) Data Setup Time SDIN, SCLK Rise Time SDIN, SCLK Fall Time Setup Time (Stop Condition) Data Hold Time Pulse width of spikes that will be suppressed t1 t2 t3 t4 t5 t6 t7 t8 t9 tps 0 600 900 5 0 600 1.3 600 600 100 300 300 400 kHz ns us ns ns ns ns ns ns ns ns
o
PP Rev 1.77 May 2003 15
WM8750L DEVICE DESCRIPTION
INTRODUCTION
Product Preview
The WM8750L is a low power audio codec offering a combination of high quality audio, advanced features, low power and small size. These characteristics make it ideal for portable digital audio applications such as MP3 and minidisk player / recorders. The device includes three stereo analogue inputs that can be switched internally. Each can be used as either a line level input, as a microphone input or be selected as a mono differential input. A programmable gain amplifier with automatic level control (ALC) keeps the recording volume constant. The on-chip stereo ADC and DAC are of a high quality using a multi-bit, low-order oversampling architecture to deliver optimum performance with low power consumption. The DAC output signal first enters an analogue mixer where an analogue input and/or the post-ALC signal can be added to it. This mix is available on line and headphone outputs. The WM8750L has a configurable digital audio interface where ADC data can be read and digital 2 audio playback data fed to the DAC. It supports a number of audio data formats including I S, DSP Mode (a burst mode in which frame sync plus 2 data packed words are transmitted), MSB-First, left justified and MSB-First, right justified, and can operate in master or slave modes. The WM8750L uses a unique clocking scheme that can generate many commonly used audio sample rates from either a 12.00MHz USB clock or an industry standard 256/384 fs clock. This feature eliminates the common requirement for an external phase-locked loop (PLL) in applications where the master clock is not an integer multiple of the sample rate. Sample rates of 8kHz, 11.025kHz, 12kHz, 16kHz, 22.05kHz, 24kHz, 32kHz, 44.1kHz, 48kHz, 88.2kHz and 96kHz can be generated. The digital filters used for recording and playback are optimised for each sampling rate used. To allow full software control over all its features, the WM8750L offers a choice of 2 or 3 wire MPU control interface. It is fully compatible and an ideal partner for a wide range of industry standard microprocessors, controllers and DSPs. The design of the WM8750L has given much attention to power consumption without compromising performance. It operates at very low voltages, and includes the ability to power off parts of the circuitry under software control, including standby and power off modes.
INPUT SIGNAL PATH
The input signal path for each channel consists of a switch to select between three analogue inputs, followed by a PGA (programmable gain amplifier) and an optional microphone gain boost. A differential input of either (LINPUT1 - RINPUT1) or (LINPUT2 - RINPUT2) may also be selected. The gain of the PGA can be controlled either by the user or by the on-chip ALC function (see Automatic Level Control). The signal then enters an ADC where it is digitised. Alternatively, the two channels can also be mixed in the analogue domain and digitised in one ADC while the other ADC is switched off. The mono-mix signal appears on both digital output channels.
SIGNAL INPUTS
The WM8750L has three sets of high impedance, low capacitance AC coupled analogue inputs, LINPUT1/RINPUT1, LINPUT2/RINPUT2 and LINPUT3/RINPUT3. The LINSEL and RINSEL control bits select between them. These inputs can be configured as microphone or line inputs by enabling or disabling the microphone gain boost. A differential input, either LINPUT1-RINPUT1 or LINPUT2RINPUT may also be selected using L/RINSEL and DS (refer to Table 4). The signal inputs are biased internally to the reference voltage VREF. Whenever the line inputs are muted or the device placed into standby mode, the inputs are kept biased to VREF using special anti-thump circuitry. This reduces any audible clicks that may otherwise be heard when changing inputs.
PP Rev 1.77 May 2003 16
Product Preview
WM8750L
DC MEASUREMENT
For DC measurements (for example, battery voltage monitoring), the input signal at the LINPUT1 and/or RINPUT1 pins can be taken directly into the respective ADC, bypassing both PGA and microphone boost. The ADC output then becomes unsigned relative to AVDD, instead of being a signed (two's complement) number relative to VREF. Setting L/RDCM will override L/RINSEL. The input range for dc measurement is AGND to AVDD. REGISTER ADDRESS R32 (20h) ADC Signal Path Control (Left) BIT 7:6 LABEL LINSEL DEFAULT 00 DESCRIPTION Left Channel Input Select 00 = LINPUT1 01 = LINPUT2 10 = LINPUT3 11 = Differential Left Channel Microphone Gain Boost 00 = Boost off (bypassed) 01 = 13dB boost 10 = 20dB boost 11 = 29dB boost Right Channel Input Select 00 = RINPUT1 01 = RINPUT2 10 = RINPUT3 11 = Differential Right Channel Microphone Gain Boost 00 = Boost off (bypassed) 01 = 13dB boost 10 = 20dB boost 11 = 29dB boost
5:4
LMICBOOST
00
R33 (21h) ADC Signal Path Control (Right)
7:6
RINSEL
00
5:4
RMICBOOST
00
Table 2 Input Software Control REGISTER ADDRESS R31 (1Fh) ADC input Mode BIT 5 LABEL RDCM DEFAULT 0 DESCRIPTION Right Channel DC Measurement 0 = Normal Operation, PGA Enabled 1 = Measure DC level on RINPUT1 Left Channel DC Measurement 0 = Normal Operation, PGA Enabled 1 = Measure DC level on LINPUT1
4
LDCM
0
Table 3 DC Measurement Select REGISTER ADDRESS R31 (1Fh) ADC Input Mode BIT 8 DS LABEL DEFAULT 0 DESCRIPTION Differential input select 0: LINPUT1 - RINPUT1 1: LINPUT2 - RINPUT2
Table 4 Differential Input Select
PP Rev 1.77 May 2003 17
WM8750L
MONO MIXING
Product Preview
The stereo ADC can operate as a stereo or mono device, or the two channels can be mixed to mono, either in the analogue domain (i.e. before the ADC) or in the digital domain (after the ADC). MONOMIX selects the mode of operation. For analogue mono mix either the left or right channel ADC can be used, allowing the unused ADC to be powered off or used for a dc measurement conversion. The user also has the flexibility to select the data output from the audio interface using DATSEL. The default is for left and right channel ADC data to be output, but the interface may also be configured so that e.g. left channel ADC data is output as both left and right data for when an analogue mono mix is selected. Note: If DC measurement is selected this overrides the MONOMIX selection. REGISTER ADDRESS R31 (1Fh) ADC input Mode BIT 7:6 LABEL MONOMIX [1:0] DEFAULT 00 DESCRIPTION 00: Stereo 01: Analogue Mono Mix (using left ADC) 10: Analogue Mono Mix (using right ADC) 11: Digital Mono Mix
Table 5 Mono Mixing
REGISTER ADDRESS R23 (17h) Additional Control (1)
BIT 3:2
LABEL DATSEL [1:0]
DEFAULT 00
DESCRIPTION 00: left data=left ADC; right data =right ADC 01: left data =left ADC; right data = left ADC 10: left data = right ADC; right data =right ADC 11: left data = right ADC; right data = left ADC
Table 6 ADC Data Output Configuration The MICBIAS output provides a low noise reference voltage suitable for biasing electret type microphones and the associated external resistor biasing network. Refer to the Applications Information section for recommended external components. The output can be enabled or disables using the MICB control bit (see also the "Power Management" section). REGISTER ADDRESS R25 (19h) Power Management (1) BIT 1 LABEL MICB DEFAULT 0 DESCRIPTION Microphone Bias Enable 0 = OFF (high impedance output) 1 = ON
Table 7 Microphone Bias Control The internal MICBIAS circuitry is shown below. Note that the is a maximum source current capability for MICBIAS is 3mA. The external biasing resistors therefore must be large enough to limit the MICBIAS current to 3mA.
VMID internal resistor
MICB
MICBIAS = 1.8 x VMID = 0.9 X AVDD
internal resistor
AGND
Figure 6 Microphone Bias Schematic
PGA CONTROL
PP Rev 1.77 May 2003 18
Product Preview
WM8750L
The PGA matches the input signal level to the ADC input range. The PGA gain is logarithmically adjustable from +30dB to -17.25dB in 0.75dB steps. Each PGA can be controlled either by the user or by the ALC function (see Automatic Level Control). When ALC is enabled for one or both channels, then writing to the corresponding PGA control register has no effect. The gain is independently adjustable on both Right and Left Line Inputs. Additionally, by controlling the register bits LIVU and RIVU, the left and right gain settings can be simultaneously updated. Setting the LZCEN and RZCEN bits enables a zero-cross detector which ensures that PGA gain changes only occur when the signal is at zero, eliminating any zipper noise. If zero cross is enabled a timeout is also available to update the gain if a zero cross does not occur. This function may be enabled by setting TOEN in register R23 (17h). The inputs can also be muted in the analogue domain under software control. The software control registers are shown in Table 8 REGISTER ADDRESS R0 (00h) Left Channel PGA 8 BIT LABEL LIVU DEFAULT 0 DESCRIPTION Left Volume Update 0 = Store LINVOL in intermediate latch (no gain change) 1 = Update left and right channel gains (left = LINVOL, right = intermediate latch) Left Channel Input Analogue Mute 1 = Enable Mute 0 = Disable Mute Note: LIVU must be set to un-mute. Left Channel Zero Cross Detector 1 = Change gain on zero cross only 0 = Change gain immediately Left Channel Input Volume Control 111111 = +30dB 111110 = +29.25dB . . 0.75dB steps down to 000000 = -17.25dB Right Volume Update 0 = Store RINVOL in intermediate latch (no gain change) 1 = Update left and right channel gains (right = RINVOL, left = intermediate latch) Right Channel Input Analogue Mute 1 = Enable Mute 0 = Disable Mute Note: RIVU must be set to un-mute. Right Channel Zero Cross Detector 1 = Change gain on zero cross only 0 = Change gain immediately Right Channel Input Volume Control 111111 = +30dB 111110 = +29.25dB . . 0.75dB steps down to 000000 = -17.25dB Timeout Enable 0 : Timeout Disabled 1 : Timeout Enabled
7
LINMUTE
1
6
LZCEN
0
5:0
LINVOL [5:0]
010111 ( 0dB )
R1 (01h) Right Channel PGA
8
RIVU
0
7
RINMUTE
1
6
RZCEN
0
5:0
RINVOL [5:0]
010111 ( 0dB )
R23 (17h) Additional Control (1)
0
TOEN
0
Table 8 Input PGA Software Control
PP Rev 1.77 May 2003 19
WM8750L
ANALOGUE TO DIGITAL CONVERTER (ADC)
Product Preview
The WM8750L uses a multi-bit, oversampled sigma-delta ADC for each channel. The use of multi-bit feedback and high oversampling rates reduces the effects of jitter and high frequency noise. The ADC Full Scale input level is proportional to AVDD. With a 3.3V supply voltage, the full scale level is 1.0 Volts r.m.s. Any voltage greater than full scale may overload the ADC and cause distortion.
ADC DIGITAL FILTER
The ADC filters perform true 24 bit signal processing to convert the raw multi-bit oversampled data from the ADC to the correct sampling frequency to be output on the digital audio interface. The digital filter path is illustrated in Figure 7.
FROM ADC
DIGITAL DECIMATOR
DIGITAL FILTER
DIGITAL HPF
TO DIGITAL AUDIO INTERFACE
ADCHPD
Figure 7 ADC Digital Filter The ADC digital filters contain a digital high pass filter, selectable via software control. The high-pass filter response is detailed in the Digital Filter Characteristics section. When the high-pass filter is enabled the dc offset is continuously calculated and subtracted from the input signal. By setting HPOR, the last calculated dc offset value is stored when the high-pass filter is disabled and will continue to be subtracted from the input signal. If the DC offset is changed, the stored and subtracted value will not change unless the high-pass filter is enabled. This feature can be used for calibration purposes. The output data format can be programmed by the user to accommodate stereo or monophonic recording on both inputs. The polarity of the output signal can also be changed under software control. The software control is shown in Table 9. REGISTER ADDRESS R5 (05h) ADC and DAC Control BIT 6:5 LABEL ADCPOL [1:0] DEFAULT 00 DESCRIPTION 00 = Polarity not inverted 01 = L polarity invert 10 = R polarity invert 11 = L and R polarity invert Store dc offset when High Pass Filter disabled 1 = store offset 0 = clear offset ADC High Pass Filter Enable (Digital) 1 = Disable High Pass Filter 0 = Enable High Pass Filter
4
HPOR
0
0
ADCHPD
0
Table 9 ADC Signal Path Control
PP Rev 1.77 May 2003 20
Product Preview
WM8750L
DIGITAL ADC VOLUME CONTROL
The output of the ADCs can be digitally amplified or attenuated over a range from -97dB to +30dB in 0.5dB steps. The volume of each channel can be controlled separately. The gain for a given eight-bit code X is given by: 0.5 x (X-195) dB for 1 X 255; MUTE for X = 0
The LAVU and RAVU control bits control the loading of digital volume control data. When LAVU or RAVU are set to 0, the LADCVOL or RADCVOL control data will be loaded into the respective control register, but will not actually change the digital gain setting. Both left and right gain settings are updated when either LAVU or RAVU are set to 1. This makes it possible to update the gain of both channels simultaneously. REGISTER ADDRESS R21 (15h) Left ADC Digital Volume BIT 7:0 LABEL LADCVOL [7:0] DEFAULT 11000011 ( 0dB ) DESCRIPTION Left ADC Digital Volume Control 0000 0000 = Digital Mute 0000 0001 = -97dB 0000 0010 = -96.5dB ... 0.5dB steps up to 1111 1111 = +30dB Left ADC Volume Update 0 = Store LADCVOL in intermediate latch (no gain change) 1 = Update left and right channel gains (left = LADCVOL, right = intermediate latch) Right ADC Digital Volume Control 0000 0000 = Digital Mute 0000 0001 = -97dB 0000 0010 = -96.5dB ... 0.5dB steps up to 1111 1111 = +30dB Right ADC Volume Update 0 = Store RADCVOL in intermediate latch (no gain change) 1 = Update left and right channel gains (left = intermediate latch, right = RADCVOL)
8
LAVU
0
R22 (16h) Right ADC Digital Volume
7:0
RADCVOL [7:0]
11000011 ( 0dB )
8
RAVU
0
Table 10 ADC Digital Volume Control
PP Rev 1.77 May 2003 21
WM8750L
AUTOMATIC LEVEL CONTROL (ALC)
Product Preview
The WM8750L has an automatic level control that aims to keep a constant recording volume irrespective of the input signal level. This is achieved by continuously adjusting the PGA gain so that the signal level at the ADC input remains constant. A digital peak detector monitors the ADC output and changes the PGA gain if necessary. Note that when the ALC function is enabled, the settings of registers 0 and 1 (LINVOL, LIVU, LIZC, RINVOL, RIVU and RIZC, but not LINMUTE and RINMUTE) are ignored.
input signal
PGA gain
signal after ALC
ALC target level
hold time
decay time
attack time
Figure 8 ALC Operation The ALC function is enabled using the ALCSEL control bits. When enabled, the recording volume can be programmed between -6dB and -28.5dB (relative to ADC full scale) using the ALCL register bits. An upper limit for the PGA gain can be imposed by setting the MAXGAIN control bits. HLD, DCY and ATK control the hold, decay and attack times, respectively: Hold time is the time delay between the peak level detected being below target and the PGA gain n beginning to ramp up. It can be programmed in power-of-two (2 ) steps, e.g. 2.67ms, 5.33ms, 10.67ms etc. up to 43.7s. Alternatively, the hold time can also be set to zero. The hold time only applies to gain ramp-up, there is no delay before ramping the gain down when the signal level is above target. Decay (Gain Ramp-Up) Time is the time that it takes for the PGA gain to ramp up across 90% of its range (e.g. from -15B up to 27.75dB). The time it takes for the recording level to return to its target value therefore depends on both the decay time and on the gain adjustment required. If the gain adjustment is small, it will be shorter than the decay time. The decay time can be programmed in n power-of-two (2 ) steps, from 24ms, 48ms, 96ms, etc. to 24.58s. Attack (Gain Ramp-Down) Time is the time that it takes for the PGA gain to ramp down across 90% of its range (e.g. from 27.75dB down to -15B gain). The time it takes for the recording level to return to its target value therefore depends on both the attack time and on the gain adjustment required. If the gain adjustment is small, it will be shorter than the attack time. The attack time can be n programmed in power-of-two (2 ) steps, from 6ms, 12ms, 24ms, etc. to 6.14s.
When operating in stereo, the peak detector takes the maximum of left and right channel peak values, and any new gain setting is applied to both left and right PGAs, so that the stereo image is preserved. However, the ALC function can also be enabled on one channel only. In this case, only one PGA is controlled by the ALC mechanism, while the other channel runs independently with its PGA gain set through the control register. When one ADC channel is unused or used for DC measurement, the peak detector disregards that channel. The ALC function can also operate when the two ADC outputs are mixed to mono in the digital domain, but not if they are mixed to mono in the analogue domain, before entering the ADCs.
PP Rev 1.77 May 2003 22
Product Preview
WM8750L
REGISTER ADDRESS R17 (11h) ALC Control 1 BIT 8:7 LABEL ALCSEL [1:0] DEFAULT 00 (OFF) DESCRIPTION ALC function select 00 = ALC off (PGA gain set by register) 01 = Right channel only 10 = Left channel only 11 = Stereo (PGA registers unused) Note: ensure that LINVOL and RINVOL settings (reg. 0 and 1) are the same before entering this mode. Set Maximum Gain of PGA 111 : +30dB 110 : +24dB ....(-6dB steps) 001 : -6dB 000 : -12dB ALC target - sets signal level at ADC input 0000 = -28.5dB FS 0001 = -27.0dB FS ... (1.5dB steps) 1110 = -7.5dB FS 1111 = -6dB FS ALC uses zero cross detection circuit.
6:4
MAXGAIN [2:0]
111 (+30dB)
3:0
ALCL [3:0]
1011 (-12dB)
R18 (12h) ALC Control 2
7
ALCZC
0 (zero cross off) 0000 (0ms)
3:0
HLD [3:0]
ALC hold time before gain is increased. 0000 = 0ms 0001 = 2.67ms 0010 = 5.33ms ... (time doubles with every step) 1111 = 43.691s ALC decay (gain ramp-up) time 0000 = 24ms 0001 = 48ms 0010 = 96ms ... (time doubles with every step) 1010 or higher = 24.58s ALC attack (gain ramp-down) time 0000 = 6ms 0001 = 12ms 0010 = 24ms ... (time doubles with every step) 1010 or higher = 6.14s
R19 (13h) ALC Control 3
7:4
DCY [3:0]
0011 (192ms)
3:0
ATK [3:0]
0010 (24ms)
Table 11 ALC Control
PEAK LIMITER
To prevent clipping when a large signal occurs just after a period of quiet, the ALC circuit includes a limiter function. If the ADC input signal exceeds 87.5% of full scale (-1.16dB), the PGA gain is ramped down at the maximum attack rate (as when ATK = 0000), until the signal level falls below 87.5% of full scale. This function is automatically enabled whenever the ALC is enabled. Note: If ATK = 0000, then the limiter makes no difference to the operation of the ALC. It is designed to prevent clipping when long attack times are used.
PP Rev 1.77 May 2003 23
WM8750L
NOISE GATE
Product Preview
When the signal is very quiet and consists mainly of noise, the ALC function may cause "noise pumping", i.e. loud hissing noise during silence periods. The WM8750L has a noise gate function that prevents noise pumping by comparing the signal level at the LINPUT1/2/3 and/or RINPUT1/2/3 pins against a noise gate threshold, NGTH. The noise gate cuts in when: * * Signal level at ADC [dB] < NGTH [dB] + PGA gain [dB] + Mic Boost gain [dB]
This is equivalent to: Signal level at input pin [dB] < NGTH [dB]
The ADC output can then either be muted or digitally attenuated by 18dB. Alternatively, the PGA gain can be held constant (preventing it from ramping up as it normally would when the signal is quiet). The table below summarises the noise gate control register. The NGTH control bits set the noise gate threshold with respect to the ADC full-scale range. The threshold is adjusted in 1.5dB steps. Levels at the extremes of the range may cause inappropriate operation, so care should be taken with set-up of the function. Note that the noise gate only works in conjunction with the ALC function, and always operates on the same channel(s) as the ALC (left, right, both, or none).
REGISTER ADDRESS R20 (14h) Noise Gate Control
BIT 7:3
LABEL NGTH [4:0]
DEFAULT 00000
DESCRIPTION Noise gate threshold 00000 -76.5dBfs 00001 -75dBfs ... 1.5 dB steps 11110 -31.5dBfs 11111 -30dBfs Noise gate type X0 = PGA gain held constant 01 = mute ADC output 11 = reserved (do not use this setting) Noise gate function enable 1 = enable 0 = disable
2:1
NGG [1:0]
00
0
NGAT
0
Table 12 Noise Gate Control
PP Rev 1.77 May 2003 24
Product Preview
WM8750L
The WM8750L has a digital 3D enhancement option to artificially increase the separation between the left and right channels. This effect can be used for recording or playback, but not for both simultaneously. Selection of 3D for record or playback is controlled by register bit MODE3D. Important: Switching the 3D filter from record to playback or from playback to record may only be done when ADC and DAC are disabled. The WM8750L control interface will only allow MODE3D to be changed when ADC and DAC are disabled (i.e. bits ADCL, ADCR, DACL and DACR in reg. 26 / 1Ah are all zero). The 3D enhancement function is activated by the 3DEN bit, and has two programmable parameters. The 3DWIDTH setting controls the degree of stereo expansion. Additionally, one of four filter characteristics can be selected for the 3D processing, using the 3DFILT control bits. REGISTER ADDRESS R16 (10h) 3D enhance 7 BIT LABEL MODE3D DEFAULT 0 DESCRIPTION Playback/Record 3D select 0 = 3D selected for Record 1 = 3D selected for Playback Upper Cut-off frequency 0 = High (2.2kHz at 48kHz sampling) 1 = Low (1.5kHz at 48kHz sampling) Lower Cut-off frequency 0 = Low (200Hz at 48kHz sampling) 1 = High (500Hz at 48kHz sampling) Stereo depth 0000: 0% (minimum 3D effect) 0001: 6.67% .... 1110: 93.3% 1111: 100% (maximum 3D effect) 3D function enable 1: enabled 0: disabled
3D STEREO ENHANCEMENT
6
3DUC
0
5
3DLC
0
4:1
3DDEPTH [3:0]
0000
0
3DEN
0
Table 13 3D Stereo Enhancement Function When 3D enhancement is enabled (and/or the graphic equaliser for playback) it may be necessary to attenuate the signal by 6dB to avoid limiting. This is a user selectable function, enabled by setting ADCDIV2 for the record path and DACDIV2 for the playback path.
REGISTER ADDRESS R5 (05h) ADC and DAC control 8
BIT
LABEL ADCDIV2
DEFAULT 0
DESCRIPTION ADC 6dB attenuate enable 0 = disabled (0dB) 1 = -6dB enabled DAC 6dB attenuate enable 0 = disabled (0dB) 1 = -6dB enabled
7
DACDIV2
0
Table 14 ADC and DAC 6dB Attenuation Select
PP Rev 1.77 May 2003 25
WM8750L
OUTPUT SIGNAL PATH
Product Preview
The WM8750L output signal paths consist of digital filters, DACs, analogue mixers and output drivers. The digital filters and DACs are enabled when the WM8750L is in `playback only' or `record and playback' mode. The mixers and output drivers can be separately enabled by individual control bits (see Analogue Outputs). Thus it is possible to utilise the analogue mixing and amplification provided by the WM8750L, irrespective of whether the DACs are running or not. The WM8750L receives digital input data on the DACDAT pin. The digital filter block processes the data to provide the following functions: * * * Digital volume control
Graphic equaliser and Dynamic Bass Boost Sigma-Delta Modulation Two high performance sigma-delta audio DACs convert the digital data into two analogue signals (left and right). These can then be mixed with analogue signals from the LINPUT1/2/3 and RINPUT1/2/3 pins, and the mix is fed to the output drivers, LOUT1/ROUT1, LOUT2/ROUT2, OUT3 and MONOOUT. * * * LOUT1/ROUT1/OUT3: can drive a 16 or 32 stereo headphone or stereo line output. LOUT2/ROUT2: can drive a 16 or 32 stereo headphone or stereo line output, or an 8 mono speaker. MONOOUT: can drive a mono line output or other load down to 10k
DIGITAL DAC VOLUME CONTROL
The signal volume from each DAC can be controlled digitally, in the same way as the ADC volume (see Digital ADC Volume Control). The gain and attenuation range is -127dB to 0dB in 0.5dB steps. The level of attenuation for an eight-bit code X is given by: 0.5 x (X-255) dB for 1 X 255; MUTE for X = 0
The LDVU and RDVU control bits control the loading of digital volume control data. When LDVU or RDVU are set to 0, the LDACVOL or RDACVOL control data is loaded into an intermediate register, but the actual gain does not change. Both left and right gain settings are updated simultaneously when either LDVU or RDVU are set to 1.
REGISTER ADDRESS R10 (0Ah) Left Channel Digital Volume
BIT 8
LABEL LDVU
DEFAULT 0
DESCRIPTION Left DAC Volume Update 0 = Store LDACVOL in intermediate latch (no gain change) 1 = Update left and right channel gains (left = LDACVOL, right = intermediate latch) Left DAC Digital Volume Control 0000 0000 = Digital Mute 0000 0001 = -127dB 0000 0010 = -126.5dB ... 0.5dB steps up to 1111 1111 = 0dB Right DAC Volume Update 0 = Store RDACVOL in intermediate latch (no gain change) 1 = Update left and right channel gains (left = intermediate latch, right = RDACVOL) Right DAC Digital Volume Control similar to LDACVOL
7:0
LDACVOL [7:0]
11111111 ( 0dB )
R11 (0Bh) Right Channel Digital Volume
8
RDVU
0
7:0
RDACVOL [7:0]
11111111 ( 0dB )
Table 15 Digital Volume Control
PP Rev 1.77 May 2003 26
Product Preview
WM8750L
GRAPHIC EQUALISER
The WM8750L has a digital graphic equaliser and adaptive bass boost function. This function operates on digital audio data before it is passed to the audio DACs. Bass enhancement can take two different forms: * Linear bass control: bass signals are amplified or attenuated by a user programmable gain. This is independent of signal volume, and very high bass gains on loud signals may lead to signal clipping. * Adaptive bass boost: The bass volume is amplified by a variable gain. When the bass volume is low, it is boosted more than when the bass volume is high. This method is recommended because it prevents clipping, and usually sounds more pleasant to the human ear. Treble control applies a user programmable gain, without any adaptive boost function. Bass and treble control are completely independent with separately programmable gains and filter characteristics.
REGISTER ADDRESS R12 (0Ch) Bass Control
BIT 7
LABEL BB 0
DEFAULT
DESCRIPTION Bass Boost 0 = Linear bass control 1 = Adaptive bass boost Bass Filter Characteristic 0 = Low Cutoff (130Hz at 48kHz sampling) 1 = High Cutoff (200Hz at 48kHz sampling) Bass Intensity Code 0000 0001 0010 0011 0100 0101 0110 0111 1000 1001 1010 1011 1100 1101 1110 1111 BB=0 +9dB +9dB +7.5dB +6dB +4.5dB +3dB +1.5dB 0dB -1.5dB -3dB -4.5dB -6dB -6dB -6dB -6dB Bypass (OFF) BB=1 15 (max) 14 13 12 11 10 9 8 7 6 5 4 3 2 1
6
BC
0
3:0
BASS [3:0]
1111 (Disabled)
R13 (0Dh) Treble Control
6
TC
0
Treble Filter Characteristic 0 = High Cutoff (8kHz at 48kHz sampling) 1 = Low Cutoff (4kHz at 48kHz sampling) Treble Intensity 0000 or 0001 = +9dB 0010 = +7.5dB ... (1.5dB steps) 1011 to 1110 = -6dB 1111 = Disable
3:0
TRBL [3:0]
1111 (Disabled)
Table 16 Graphic equaliser
PP Rev 1.77 May 2003 27
WM8750L
DIGITAL TO ANALOGUE CONVERTER (DAC)
Product Preview
After passing through the graphic equaliser filters, digital `de-emphasis' can be applied to the audio data if necessary (e.g. when the data comes from a CD with pre-emphasis used in the recording). De-emphasis filtering is available for sample rates of 48kHz, 44.1kHz and 32kHz. The WM8750L also has a Soft Mute function, which gradually attenuates the volume of the digital signal to zero. When removed, the gain will ramp back up to the digital gain setting. This function is enabled by default. To play back an audio signal, it must first be disabled by setting the DACMU bit to zero. REGISTER ADDRESS R5 (05h) ADC and DAC Control BIT 2:1 LABEL DEEMP [1:0] DEFAULT 00 DESCRIPTION De-emphasis Control 11 = 48kHz sample rate 10 = 44.1kHz sample rate 01 = 32kHz sample rate 00 = No De-emphasis Digital Soft Mute 1 = mute 0 = no mute (signal active)
3
DACMU
1
Table 17 DAC Control The digital audio data is converted to oversampled bit streams in the on-chip, true 24-bit digital interpolation filters. The bitstream data enters two multi-bit, sigma-delta DACs, which convert them to high quality analogue audio signals. The multi-bit DAC architecture reduces high frequency noise and sensitivity to clock jitter. It also uses a Dynamic Element Matching technique for high linearity and low distortion. In normal operation, the left and right channel digital audio data is converted to analogue in two separate DACs. However, it is also possible to disable one channel, so that the same signal (left or right) appears on both analogue output channels. Additionally, there is a mono-mix mode where the two audio channels are mixed together digitally and then converted to analogue using only one DAC, while the other DAC is switched off. The mono-mix signal can be selected to appear on both analogue output channels. The DAC output defaults to non-inverted. Setting DACINV will invert the DAC output phase on both left and right channels. REGISTER ADDRESS R23 (17h) Additional Control (1) BIT 5:4 LABEL DMONOMIX [1:0] DEFAULT 00 DESCRIPTION DAC mono mix 00: stereo 01: mono ((L+R)/2) into DACL, `0' into DACR 10: mono ((L+R)/2) into DACR, `0' into DACL 11: mono ((L+R)/2) into DACL & DACR DAC phase invert 0 : non-inverted 1 : inverted
1
DACINV
0
Table 18 DAC Mono Mix and Phase Invert Select
PP Rev 1.77 May 2003 28
Product Preview
WM8750L
OUTPUT MIXERS
The WM8750L provides the option to mix the DAC output signal with analogue line-in signals from the LINPUT1/2/3, RINPUT1/2/3 pins or a mono differential input (LINPUT1 - RINPUT1) or (LINPUT2 - RINPUT2), selected by DS (see Table 4) . The level of the mixed-in signals can be controlled with PGAs (Programmable Gain Amplifiers). REGISTER ADDRESS R34 (22h) Left Mixer (1) BIT 2:0 LABEL LMIXSEL DEFAULT 000 DESCRIPTION Left Input Selection for Output Mix 000 = LINPUT1 001 = LINPUT2 010 = LINPUT3 011 = Left ADC Input (after PGA / MICBOOST) 100 = Differential input Right Input Selection for Output Mix 000 = RINPUT1 001 = RINPUT2 010 = RINPUT3 011 = Right ADC Input (after PGA / MICBOOST) 100 = Differential input
R36 (24h) Right Mixer (1)
2:0
RMIXSEL
000
Table 19 Output Mixer Signal Selection
REGISTER ADDRESS R34 (22h) Left Mixer Control (1)
BIT 8
LABEL LD2LO
DEFAULT 0
DESCRIPTION Left DAC to Left Mixer 0 = Disable (Mute) 1 = Enable Path LMIXSEL Signal to Left Mixer 0 = Disable (Mute) 1 = Enable Path LMIXSEL Signal to Left Mixer Volume 000 = +6dB ... (3dB steps) 111 = -15dB Right DAC to Left Mixer 0 = Disable (Mute) 1 = Enable Path RMIXSEL Signal to Left Mixer 0 = Disable (Mute) 1 = Enable Path RMIXSEL Signal to Left Mixer Volume 000 = +6dB ... (3dB steps) 111 = -15dB
7
LI2LO
0
6:4
LI2LOVOL [2:0]
101 (-9dB)
R35 (23h) Left Mixer Control (2)
8
RD2LO
0
7
RI2LO
0
6:4
RI2LOVOL [2:0]
101 (-9dB)
Table 20 Left Output Mixer Control
PP Rev 1.77 May 2003 29
WM8750L
REGISTER ADDRESS R36 (24h) Right Mixer Control (1) BIT 8 LABEL LD2RO DEFAULT 0
Product Preview
DESCRIPTION Left DAC to Right Mixer 0 = Disable (Mute) 1 = Enable Path LMIXSEL Signal to Right Mixer 0 = Disable (Mute) 1 = Enable Path LMIXSEL Signal to Right Mixer Volume 000 = +6dB ... (3dB steps) 111 = -15dB Right DAC to Right Mixer 0 = Disable (Mute) 1 = Enable Path RMIXSEL Signal to Right Mixer 0 = Disable (Mute) 1 = Enable Path RMIXSEL Signal to Right Mixer Volume 000 = +6dB ... (3dB steps) 111 = -15dB
7
LI2RO
0
6:4
LI2ROVOL [2:0]
101 (-9dB)
R37 (25h) Right Mixer Control (2)
8
RD2RO
0
7
RI2RO
0
6:4
RI2ROVOL [2:0]
101 (-9dB)
Table 21 Right Output Mixer Control
REGISTER ADDRESS R38 (26h) Mono Mixer Control (1)
BIT 8
LABEL LD2MO
DEFAULT 0
DESCRIPTION Left DAC to Mono Mixer 0 = Disable (Mute) 1 = Enable Path LMIXSEL Signal to Mono Mixer 0 = Disable (Mute) 1 = Enable Path LMIXSEL Signal to Mono Mixer Volume 000 = +6dB ... (3dB steps) 111 = -15dB Right DAC to Mono Mixer 0 = Disable (Mute) 1 = Enable Path RMIXSEL Signal to Mono Mixer 0 = Disable (Mute) 1 = Enable Path RMIXSEL Signal to Mono Mixer Volume 000 = +6dB ... (3dB steps) 111 = -15dB
7
LI2MO
0
6:4
LI2MOVOL [2:0]
101 (-9dB)
R39 (27h) Mono Mixer Control (2)
8
RD2MO
0
7
RI2MO
0
6:4
RI2MOVOL [2:0]
101 (-9dB)
Table 22 Mono Output Mixer Control
PP Rev 1.77 May 2003 30
Product Preview
WM8750L
ANALOGUE OUTPUTS
LOUT1/ROUT1 OUTPUTS
The LOUT1 and ROUT1 pins can drive a 16 or 32 headphone or a line output (see Headphone Output and Line Output sections, respectively). The signal volume on LOUT1 and ROUT1 can be independently adjusted under software control by writing to LOUT1VOL and ROUT1VOL, respectively. Note that gains over 0dB may cause clipping if the signal is large. Any gain setting below 0101111 (minimum) mutes the output driver. The corresponding output pin remains at the same DC level (the reference voltage on the VREF pin), so that no click noise is produced when muting or un-muting. A zero cross detect on the analogue output may also be enabled when changing the gain setting to minimize audible clicks and zipper noise as the gain updates. If zero cross is enabled a timeout is also available to update the gain if a zero cross does not occur. This function may be enabled by setting TOEN in register R23 (17h). REGISTER ADDRESS R2 (02h) LOUT1 Volume BIT 8 LABEL LO1VU DEFAULT 0 DESCRIPTION Left Volume Update 0 = Store LOUT1VOL in intermediate latch (no gain change) 1 = Update left and right channel gains (left = LOUT1VOL, right = intermediate latch) Left zero cross enable 1 = Change gain on zero cross only 0 = Change gain immediately LOUT1 Volume 1111111 = +6dB ... (80 steps) 0110000 = -67dB 0101111 to 0000000 = Analogue MUTE Right Volume Update 0 = Store ROUT1VOL in intermediate latch (no gain change) 1 = Update left and right channel gains (left = intermediate latch, right = ROUT1VOL) Left zero cross enable 1 = Change gain on zero cross only 0 = Change gain immediately ROUT1 Volume Similar to LOUT1VOL
7
LO1ZC
0
6:0
LOUT1VOL [6:0]
1111001 (0dB)
R3 (03h) ROUT1 Volume
8
RO1VU
0
7
RO1ZC
0
6:0
ROUT1VOL [6:0]
1111001
Table 23 LOUT1/ROUT1 Volume Control
PP Rev 1.77 May 2003 31
WM8750L
LOUT2/ROUT2 OUTPUTS
Product Preview
The LOUT2 and ROUT2 output pins are essentially similar to LOUT1 and ROUT1, but they are independently controlled and can also drive an 8 mono speaker (see Speaker Output section). For speaker drive, the ROUT2 signal must be inverted (ROUT2INV = 1), so that the left and right channel are mixed to mono in the speaker [L-(-R) = L+R]. REGISTER ADDRESS R40 (28h) LOUT2 Volume BIT 6:0 7 LABEL LOUT2VOL [6:0] LO2ZC DEFAULT 1111001 (0dB) 0 DESCRIPTION Similar to LOUT1VOL Left zero cross enable 1 = Change gain on zero cross only 0 = Change gain immediately Same as LO1VU Similar ROUT1VOL Left zero cross enable 1 = Change gain on zero cross only 0 = Change gain immediately Same as RO1VU ROUT2 Invert 0 = No Inversion (0 phase shift) 1 = Signal inverted (180 phase shift)
8 R41 (29h) ROUT2 Volume 6:0 7
LO2VU ROUT2VOL [6:0] RO2ZC
0 1111001 (0dB) 0
8 R24 (18h) Additional Control (2) 4
RO2VU ROUT2INV
0 0
Table 24 LOUT2/ROUT2 Volume Control
MONO OUTPUT
The MONOOUT pin can drive a mono line output. The signal volume on MONOOUT can be adjusted under software control by writing to MONOOUTVOL. REGISTER ADDRESS R42 (2Ah) MONOOUT Volume BIT 6:0 LABEL MONOOUT VOL [6:0] DEFAULT 1111001 (0dB) DESCRIPTION MONOOUT Volume 1111111 = +6dB ... (80 steps) 0110000 = -67dB 0101111 to 0000000 = Analogue MUTE MONOOUT zero cross enable 1 = Change gain on zero cross only 0 = Change gain immediately
7
MOZC
0
Table 25 MONOOUT Volume Control
OUT3 OUTPUT
The OUT3 pin can drive a 16 or 32 headphone or a line output or be used as a DC reference for a headphone output (see Headphone Output section). It can be selected to either drive out an inverted ROUT1 or inverted MONOOUT for e.g. an earpiece drive between OUT3 and LOUT1 or differential output between OUT3 and MONOOUT. OUT3SW selects the mode of operation required. REGISTER ADDRESS R24 (18h) Additional Control (2) BIT 8:7 LABEL OUT3SW [1:0] DEFAULT 00 DESCRIPTION OUT3 select 00 : VREF 01 : ROUT1 signal (volume controlled by ROUT1VOL) 10 : MONOOUT 11 : right mixer output (no volume control through ROUT1VOL)
Table 26 OUT3 Select
PP Rev 1.77 May 2003 32
Product Preview
WM8750L
Each analogue output of the WM8750L can be separately enabled or disabled. The analogue mixer associated with each output is powered on or off along with the output pin. All outputs are disabled by default. To save power, unused outputs should remain disabled. Outputs can be enabled at any time, except when VREF is disabled (VR=0), as this may cause pop noise (see "Power Management" and "Applications Information" sections) REGISTER ADDRESS R26 (1Ah) Power Management (2) BIT 6 5 4 3 2 1 LABEL LOUT1 ROUT1 LOUT2 ROUT2 MONO OUT3 0 0 0 0 0 0 DEFAULT DESCRIPTION LOUT1 Enable ROUT1 Enable LOUT2 Enable ROUT2 Enable MONOOUT Enable OUT3 Enable
ENABLING THE OUTPUTS
Note: All "Enable" bits are 1 = ON, 0 = OFF Table 27 Analogue Output Control Whenever an analogue output is disabled, it remains connected to VREF (pin 20) through a resistor. This helps to prevent pop noise when the output is re-enabled. The resistance between VREF and each output can be controlled using the VROI bit in register 27. The default is low (1.5k), so that any capacitors on the outputs can charge up quickly at start-up. If a high impedance is desired for disabled outputs, VROI can then be set to 1, increasing the resistance to about 40k. REGISTER ADDRESS R27 (1Bh) Additional (1) BIT 6 LABEL VROI 0 DEFAULT DESCRIPTION VREF to analogue output resistance 0: 1.5 k 1: 40 k
Table 28 Disabled outputs to VREF resistance
HEADPHONE SWITCH
The RINPUT3/HPDETECT pin can be used as a headphone switch control input to automatically disable the speaker output and enable the headphone output e.g. when a headphone is plugged into a jack socket. In this mode, enabled by setting HPSWEN, HPDETECT switches between headphone and speaker outputs (e.g. when the pin is connected to a mechanical switch in the headphone socket to detect plug-in). The HPSWPOL bit reverses the pin's polarity. Note that the LOUT1, ROUT1, LOUT2 and ROUT2 bits in register 26 must also be set for headphone and speaker output (see Table 29 and Table 30). Note: When RINPUT3/HPDETECT is used as the HPDETECT input, the thresholds become CMOS levels (0.3 AVDD / 0.7 AVDD). HPSWEN 0 0 0 0 1 1 1 1 1 1 1 1 HPSWPOL HPDETECT (PIN23) X X X X 0 0 0 0 1 1 1 1 X X X X 0 0 1 1 0 0 1 1 L/ROUT1 (reg. 26) 0 0 1 1 X X 0 1 X X 0 1 L/ROUT2 (reg. 26) 0 1 0 1 0 1 X X 0 1 X X Headphone enabled no no yes yes no no no yes no yes no no Speaker enabled no yes no yes no yes no no no no no yes
Table 29 Headphone Switch Operation PP Rev 1.77 May 2003 33
WM8750L
REGISTER ADDRESS R24 (18h) Additional Control (2) BIT 6 LABEL HPSWEN 0 DEFAULT
Product Preview DESCRIPTION Headphone Switch Enable 0 : Headphone switch disabled 1 : Headphone switch enabled Headphone Switch Polarity 0 : HPDETECT high = headphone 1 : HPDETECT high = speaker
5
HPSWPOL
0
Table 30 Headphone Switch
HPSWEN = 1 HPSWPOL = 1 L/ROUT1 = L/ROUT2 = 1 headphone / speaker switching
AVDD ROUT1 LOUT1 47k / 100k HPDETECT
L R
+
Figure TBD Example Headset Detection circuit using normally-open switch
+
switch closes on insertion
HPSWEN = 1 HPSWPOL = 0 L/ROUT1 = L/ROUT2 = 1 headphone / speaker switching
AVDD ROUT1 LOUT1 47k / 100k HPDETECT
L switch opens on insertion
+
R
Figure TBD Example Headset Detection circuit using normally-closed switch
+
PP Rev 1.77 May 2003 34
Product Preview
WM8750L
The speaker and headphone outputs can drive very large currents. To protect the WM8750L from overheating a thermal shutdown circuit is included. If the device temperature reaches approximately 0 150 C and the thermal shutdown circuit is enabled (TSDEN = 1 ) then the speaker and headphone amplifiers (outputs OUT1L/R, OUT2L/R & OUT3) will be disabled. REGISTER ADDRESS R23 (17h) Additional Control (1) BIT 8 LABEL TSDEN 0 DEFAULT DESCRIPTION Thermal Shutdown Enable 0 : thermal shutdown disabled 1 : thermal shutdown enabled
THERMAL SHUTDOWN
Table 31 Thermal Shutdown
HEADPHONE OUTPUT
Analogue outputs LOUT1/ROUT1, LOUT2/ROUT2, and OUT3, can drive a 16 or 32 headphone load, either through DC blocking capacitors, or DC coupled without any capacitor.
Headphone Output using DC blocking capacitors
C1 220uF
DC Coupled Headphone Output (OUT3SW = 00)
LOUT1/2 ROUT1/2 WM8750L
LOUT1/2
C2 220uF HPGND = 0V
WM8750L
ROUT1/2 OUT3 = VREF
Figure 9 Recommended Headphone Output Configurations When DC blocking capacitors are used, then their capacitance and the load resistance together determine the lower cut-off frequency, fc. Increasing the capacitance lowers fc, improving the bass response. Smaller capacitance values will diminish the bass response. Assuming a 16 Ohm load and C1, C2 = 220F: fc = 1 / 2 RLC1 = 1 / (2 x 16 x 220F) = 45 Hz In the DC coupled configuration, the headphone "ground" is connected to the OUT3 pin, which must be enabled by setting OUT3 = 1 and OUT3SW = 00. As the OUT3 pin produces a DC voltage of AVDD/2 (=VREF), there is no DC offset between LOUT1/ROUT1 and OUT3, and therefore no DC blocking capacitors are required. This saves space and material cost in portable applications. It is recommended to connect the DC coupled headphone outputs only to headphones, and not to the line input of another device. Although the built-in short circuit protection will prevent any damage to the headphone outputs, such a connection may be noisy, and may not function properly if the other device is grounded.
SPEAKER OUTPUT
LOUT2 and ROUT2 can differentially drive a mono 8 speaker as shown below.
LEFT MIXER
LOUT2
WM8750L
ROUT2INV = 1 -1
LOUT2VOL
VSPKR = L-(-R) = L+R
ROUT2
RIGHT MIXER
ROUT2VOL
Figure 10 Speaker Output Connection The right channel is inverted by setting the ROUT2INV bit, so that the signal across the loudspeaker is the sum of left and right channels.
PP Rev 1.77 May 2003 35
WM8750L
LINE OUTPUT
Product Preview
The analogue outputs, LOUT1/ROUT1 and LOUT2/ROUT2, can be used as line outputs. Additionally, OUT3 and MONOOUT can be used as a stereo line-out by setting OUT3SW=11 (reg. 24) and ensuring the contents of registers 38 and 39 (mono-out mix) are the same as reg. 34 and 35 (left out mix). Recommended external components are shown below.
C1 1uF LOUT1/2 or OUT3 (OUT3SW=11) R1 100 Ohm LINE-OUT SOCKET (LEFT)
WM8750L
ROUT1/2 or MONOOUT C2 1uF R2 100 Ohm
AGND
AGND
LINE-OUT SOCKET (RIGHT)
Figure 11 Recommended Circuit for Line Output The DC blocking capacitors and the load resistance together determine the lower cut-off frequency, fc. Assuming a 10 kOhm load and C1, C2 = 1F: fc = 1 / 2 (RL+R1) C1 = 1 / (2 x 10.1k x 1F) = 16 Hz Increasing the capacitance lowers fc, improving the bass response. Smaller values of C1 and C2 will diminish the bass response. The function of R1 and R2 is to protect the line outputs from damage when used improperly.
DIGITAL AUDIO INTERFACE
The digital audio interface is used for inputting DAC data into the WM8750L and outputting ADC data from it. It uses five pins: * * * * * ADCDAT: ADC data output ADCLRC: ADC data alignment clock DACDAT: DAC data input ADCLRC: DAC data alignment clock BCLK: Bit clock, for synchronisation
The clock signals BCLK, ADCLRC and DACLRC can be outputs when the WM8750L operates as a master, or inputs when it is a slave (see Master and Slave Mode Operation, below). Four different audio data formats are supported: * * * * Left justified Right justified 2 IS DSP mode
All four of these modes are MSB first. They are described in Audio Data Formats, below. Refer to the Electrical Characteristic section for timing information.
MASTER AND SLAVE MODE OPERATION
The WM8750L can be configured as either a master or slave mode device. As a master device the WM8750L generates BCLK, ADCLRC and DACLRC and thus controls sequencing of the data transfer on ADCDAT and DACDAT. In slave mode, the WM8750L responds with data to clocks it receives over the digital audio interface. The mode can be selected by writing to the MS bit (see Table 23). Master and slave modes are illustrated below.
BCLK ADCLRC WM8750 CODEC DACLRC ADCDAT DACDAT DSP ENCODER/ DECODER
WM8750 CODEC
BCLK ADCLRC DACLRC ADCDAT DACDAT DSP ENCODER/ DECODER
Note: The ADC and DAC can run at different sample rates
Note: The ADC and DAC can run at different sample rates
Figure 12 Master Mode
Figure 13 Slave Mode
PP Rev 1.77 May 2003 36
Product Preview
WM8750L
AUDIO DATA FORMATS
In Left Justified mode, the MSB is available on the first rising edge of BCLK following a LRCLK transition. The other bits up to the LSB are then transmitted in order. Depending on word length, BCLK frequency and sample rate, there may be unused BCLK cycles before each LRCLK transition.
1/fs
LEFT CHANNEL DACLRC/ ADCLRC
RIGHT CHANNEL
BCLK
DACDAT/ ADCDAT
1
2
3
n-2 n-1
n
1
2
3
n-2 n-1
n
MSB
Input Word Length (WL)
LSB
MSB
LSB
Note: Input word length is defined by the WL register. Timing is shown with LRP = 1
Figure 14 Left Justified Audio Interface (assuming n-bit word length) In Right Justified mode, the LSB is available on the last rising edge of BCLK before a LRCLK transition. All other bits are transmitted before (MSB first). Depending on word length, BCLK frequency and sample rate, there may be unused BCLK cycles after each LRCLK transition.
1/fs
LEFT CHANNEL DACLRC/ ADCLRC
RIGHT CHANNEL
BCLK
DACDAT/ ADCDAT
1
2
3
n-2 n-1
n
1
2
3
n-2 n-1
n
MSB
Input Word Length (WL)
LSB
MSB
LSB
Note: Input word length is defined by the WL register. Timing is shown with LRP = 1
Figure 15 Right Justified Audio Interface (assuming n-bit word length) In I S mode, the MSB is available on the second rising edge of BCLK following a LRCLK transition. The other bits up to the LSB are then transmitted in order. Depending on word length, BCLK frequency and sample rate, there may be unused BCLK cycles between the LSB of one sample and the MSB of the next.
1/fs
2
LEFT CHANNEL DACLRC/ ADCLRC
RIGHT CHANNEL
BCLK
1 BCLK 1 BCLK 3 n-2 n-1 n 1 2 3 n-2 n-1 n
DACDAT/ ADCDAT
1
2
MSB
Input Word Length (WL)
LSB
MSB
LSB
Note: Input word length is defined by the WL register. Timing is shown with LRP = 1
Figure 16 I S Justified Audio Interface (assuming n-bit word length) In DSP mode, the left channel MSB is available on either the 1 (mode B) or 2 (mode A) rising edge of BCLK (selectable by LRP) following a rising edge of LRCLK. Right channel data immediately PP Rev 1.77 May 2003 37
st nd
2
WM8750L
Product Preview follows left channel data. Depending on word length, BCLK frequency and sample rate, there may be unused BCLK cycles between the LSB of the right channel data and the next sample.
1/fs 1 BCLK
DACLRC/ ADCLRC
BCLK
LEFT CHANNEL DACDAT/ ADCDAT
1 2 3 n-2 n-1 n 1 2
RIGHT CHANNEL
3 n-2 n-1 n
MSB
Input Word Length (WL)
LSB
Figure 17 DSP Mode Audio Interface (mode A, LRP=0)
1/fs 1 BCLK
DACLRC/ ADCLRC
BCLK
LEFT CHANNEL DACDAT/ ADCDAT
1 2 3 n-2 n-1 n 1 2
RIGHT CHANNEL
3 n-2 n-1 n
MSB
Input Word Length (WL)
LSB
Figure 18 DSP Mode Audio Interface (mode B, LRP=1)
PP Rev 1.77 May 2003 38
Product Preview
WM8750L
The register bits controlling audio format, word length and master / slave mode are summarised in Table 32. MS selects audio interface operation in master or slave mode. In Master mode BCLK, ADCLRC and DACLRC are outputs. The frequency of ADCLRC and DACLRC is set by the sample rate control bits SR[4:0] and USB. In Slave mode BCLK, ADCLRC and DACLRC are inputs. REGISTER ADDRESS R7 (07h) Digital Audio Interface Format BIT 7 LABEL BCLKINV DEFAULT 0 DESCRIPTION BCLK invert bit (for master & slave modes) 0 = BCLK not inverted 1 = BCLK inverted Master / Slave Mode Control 1 = Enable Master Mode 0 = Enable Slave Mode Left/Right channel swap 1 = swap left & right DAC data in audio interface 0 = output left and right data as normal right, left & i2s modes - LRCLK polarity 1 = invert LRCLK polarity 0 = normal LRCLK polarity DSP Mode - mode A/B select 1 = MSB is available on 1st BCLK rising edge after LRC rising edge (mode B) 0 = MSB is available on 2nd BCLK rising edge after LRC rising edge (mode A) 3:2 WL[1:0] 10 Audio Data Word Length 11 = 32 bits (see Note) 10 = 24 bits 01 = 20 bits 00 = 16 bits Audio Data Format Select 11 = DSP Mode 2 10 = I S Format 01 = Left justified 00 = Right justified
AUDIO INTERFACE CONTROL
6
MS
0
5
LRSWAP
0
4
LRP
0
1:0
FORMAT[1:0]
10
Table 32 Audio Data Format Control Note: Right Justified mode does not support 32-bit data.
AUDIO INTERFACE OUTPUT TRISTATE
Register bit TRI, register 24(18h) bit[3] can be used to tristate the ADCDAT pin and switch ADCLRC, DACLRC and BCLK to inputs. In Slave mode (MASTER=0) ADCLRC, DACLRC and BCLK are by default configured as inputs and only ADCDAT will be tri-stated, (see Table 33). REGISTER ADDRESS R24(18h) Additional Control (2) BIT 3 LABEL TRI DEFAULT 0 DESCRIPTION Tristates ADCDAT and switches ADCLRC, DACLRC and BCLK to inputs. 0 = ADCDAT is an output, ADCLRC, DACLRC and BCLK are inputs (slave mode) or outputs (master mode) 1 = ADCDATE is tristated, ADCLRC, DACLRC and BCLK are inputs
Table 33 Tri-stating the Audio Interface
PP Rev 1.77 May 2003 39
WM8750L
MASTER MODE ADCLRC AND DACLRC ENABLE
Product Preview
In Master mode, by default ADCLRC is disabled when the ADC is disabled and DACLRC is disabled when the DAC is disabled. Register bit LRCM, register 24(18h) bit[2] changes the control so that the ADCLRC and DACLRC are disabled only when ADC and DAC are disabled. This enables the user to use e.g. ADCLRC for both ADC and DAC LRCLK and disable the ADC when DAC only operation is required, (see Table 34). REGISTER ADDRESS R24(18h) Additional Control (2) BIT 2 LABEL LRCM DEFAULT 0 DESCRIPTION Selects disable mode for ADCLRC and DACLRC 0 = ADCLRC disabled when ADC disabled, DACLRC disabled when DAC disabled 1 = ADCLRC and DACLRC disabled only when ADC and DAC are disabled
Table 34 ADCLRC/DACLRC Enable
CLOCK OUTPUT
By default ADCLRC (pin 9) is the ADC word clock input/output. Under the control of ADCLRM[1:0], register 27(1Bh) bits [8:7] the ADCLRC pin may be configured as a clock output. If ADCLRM is 01, 10 or 11 then ADCLRC pin is always an output even in slave mode or when TRI = `1', (see Table 35). REGISTER ADDRESS R27(18h) Additional Control (3) BIT LABEL DEFAULT 00 DESCRIPTION Configures ADCLRC pin 00 = ADCLRC is ADC word clock input (slave mode) or ADCLRC output (master mode) 01 = ADCLRC pin is MCLK output 10 = ADCLRC pin is MCLK / 5.5 output 11 = ADCLRC pin is MCLK / 6 output
[8:7] ADCLRM [1:0]
Table 35 ADCLRC Clock Output
CLOCKING AND SAMPLE RATES
The WM8750L supports a wide range of master clock frequencies on the MCLK pin, and can generate many commonly used audio sample rates directly from the master clock. The ADC and DAC do not need to run at the same sample rate; several different combinations are possible. There are two clocking modes: * * `Normal' mode supports master clocks of 128fs, 192fs, 256fs, 384fs, and their multiples (Note: fs refers to the ADC or DAC sample rate, whichever is faster) USB mode supports 12MHz or 24MHz master clocks. This mode is intended for use in systems with a USB interface, and eliminates the need for an external PLL to generate another clock frequency for the audio codec. REGISTER ADDRESS R8 (08h) Clocking and Sample Rate Control 6 BIT LABEL CLKDIV2 0 DEFAULT DESCRIPTION Master Clock Divide by 2 1 = MCLK is divided by 2 0 = MCLK is not divided Sample Rate Control Clocking Mode Select 1 = USB Mode 0 = `Normal' Mode
5:1 0
SR [4:0] USB
0000 0
Table 36 Clocking and Sample Rate Control The clocking of the WM8750L is controlled using the CLKDIV2, USB, and SR control bits. Setting the CLKDIV2 bit divides MCLK by two internally. The USB bit selects between `Normal' and USB mode. Each value of SR[4:0] selects one combination of MCLK division ratios and hence one combination of sample rates (see next page). Since all sample rates are generated by dividing MCLK, their accuracy depends on the accuracy of MCLK. If MCLK changes, the sample rates change proportionately. Note that some sample rates (e.g. 44.1kHz in USB mode) are approximated, i.e. they differ from their target value by a very small amount. This is not audible, as the maximum deviation is only 0.27% PP Rev 1.77 May 2003 40
Product Preview
WM8750L
(8.0214kHz instead of 8kHz in USB mode). By comparison, a half-tone step corresponds to a 5.9% change in pitch.
MCLK CLKDIV2=0 12.288 MHz
MCLK CLKDIV2=1
ADC SAMPLE RATE (ADCLRC)
DAC SAMPLE RATE (DACLRC)
USB
SR [4:0]
FILTER TYPE 1 1 1 1 1 1 1 1 3 1 1 1 1 1 1 3 1 1 1 1 1 1 1 1 3 1 1 1 1 1 1 3 0 0 1 1 1 0 0 1 0 0 1 1 0 0 3 2
BCLK (MS=1) MCLK/4 MCLK/4 MCLK/4 MCLK/4 MCLK/4 MCLK/4 MCLK/4 MCLK/4 MCLK/2 MCLK/4 MCLK/4 MCLK/4 MCLK/4 MCLK/4 MCLK/4 MCLK/2 MCLK/6 MCLK/6 MCLK/6 MCLK/6 MCLK/6 MCLK/6 MCLK/6 MCLK/6 MCLK/3 MCLK/6 MCLK/6 MCLK/6 MCLK/6 MCLK/6 MCLK/6 MCLK/3 MCLK MCLK MCLK MCLK MCLK MCLK MCLK MCLK MCLK MCLK MCLK MCLK MCLK MCLK MCLK MCLK
`Normal' Clock Mode (`*' indicates backward compatibility with WM8731) 8 kHz (MCLK/1536) 8 kHz (MCLK/1536) 24.576 MHz 8 kHz (MCLK/1536) 48 kHz (MCLK/256) 12 kHz (MCLK/1024) 12 kHz (MCLK/1024) 16 kHz (MCLK/768) 16 kHz (MCLK/768) 24 kHz (MCLK/512) 24 kHz (MCLK/512) 32 kHz (MCLK/384) 32 kHz (MCLK/384) 48 kHz (MCLK/256) 8 kHz (MCLK/1536) 48 kHz (MCLK/256) 48 kHz (MCLK/256) 96 kHz (MCLK/128) 96 kHz (MCLK/128) 8.0182 kHz (MCLK/1408) 8.0182 kHz (MCLK/1408) 11.2896MHz 22.5792MHz 8.0182 kHz (MCLK/1408) 44.1 kHz (MCLK/256) 11.025 kHz (MCLK/1024) 11.025 kHz (MCLK/1024) 22.05 kHz (MCLK/512) 22.05 kHz (MCLK/512) 44.1 kHz (MCLK/256) 8.0182 kHz (MCLK/1408) 44.1 kHz (MCLK/256) 44.1 kHz (MCLK/256) 88.2 kHz (MCLK/128) 88.2 kHz (MCLK/128) 8 kHz (MCLK/2304) 8 kHz (MCLK/2304) 18.432MHz 36.864MHz 8 kHz (MCLK/2304) 48 kHz (MCLK/384) 12 kHz (MCLK/1536) 12 kHz (MCLK/1536) 16kHz (MCLK/1152) 16 kHz (MCLK/1152) 24kHz (MCLK/768) 24 kHz (MCLK/768) 32 kHz (MCLK/576) 32 kHz (MCLK/576) 48 kHz (MCLK/384) 48 kHz (MCLK/384) 48 kHz (MCLK/384) 8 kHz (MCLK/2304) 96 kHz (MCLK/192) 96 kHz (MCLK/192) 8.0182 kHz (MCLK/2112) 8.0182 kHz (MCLK/2112) 16.9344MHz 33.8688MHz 8.0182 kHz (MCLK/2112) 44.1 kHz (MCLK/384) 11.025 kHz (MCLK/1536) 11.025 kHz (MCLK/1536) 22.05 kHz (MCLK/768) 22.05 kHz (MCLK/768) 44.1 kHz (MCLK/384) 8.0182 kHz (MCLK/2112) 44.1 kHz (MCLK/384) 44.1 kHz (MCLK/384) 88.2 kHz (MCLK/192) 88.2 kHz (MCLK/192) USB Mode (`*' indicates backward compatibility with WM8731) 8 kHz (MCLK/1500) 8 kHz (MCLK/1500) 12.000MHz 24.000MHz 8 kHz (MCLK/1500) 48 kHz (MCLK/250) 8.0214 kHz (MCLK/1496) 8.0214kHz (MCLK/1496) 8.0214 kHz (MCLK/1496) 44.118 kHz (MCLK/272) 11.0259 kHz (MCLK/1088) 11.0259kHz (MCLK/1088) 12 kHz (MCLK/1000) 12 kHz (MCLK/1000) 16kHz (MCLK/750) 16kHz (MCLK/750) 22.0588kHz (MCLK/544) 22.0588kHz (MCLK/544) 24kHz (MCLK/500) 24kHz (MCLK/500) 32 kHz (MCLK/375) 32 kHz (MCLK/375) 44.118 kHz (MCLK/272) 8.0214kHz (MCLK/1496) 44.118 kHz (MCLK/272) 44.118 kHz (MCLK/272) 48 kHz (MCLK/250) 8 kHz (MCLK/1500) 48 kHz (MCLK/250) 48 kHz (MCLK/250) 88.235kHz (MCLK/136) 88.235kHz (MCLK/136) 96 kHz (MCLK/125) 96 kHz (MCLK/125) Table 37 Master Clock and Sample Rates
0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
00110 * 00100 * 01000 01010 11100 01100 * 00010 * 00000 * 01110 * 10110 * 10100 * 11000 11010 10010 * 10000 * 11110 * 00111 * 00101 * 01001 01011 11101 01101 * 00001 * 00011 * 01111 * 10111 * 10101 * 11001 11011 10011 * 10001 * 11111 * 00110 * 00100 * 10111 * 10101 * 11001 01000 01010 11011 11100 01100 * 10011 * 10001 * 00010 * 00000 * 11111 * 01110 *
PP Rev 1.77 May 2003 41
WM8750L
CONTROL INTERFACE
SELECTION OF CONTROL MODE
Product Preview
The WM8750L is controlled by writing to registers through a serial control interface. A control word consists of 16 bits. The first 7 bits (B15 to B9) are address bits that select which control register is accessed. The remaining 9 bits (B8 to B0) are data bits, corresponding to the 9 bits in each control register. The control interface can operate as either a 3-wire or 2-wire MPU interface. The MODE pin selects the interface format. MODE Low High INTERFACE FORMAT 2 wire 3 wire
Table 38 Control Interface Mode Selection
3-WIRE SERIAL CONTROL MODE
In 3-wire mode, every rising edge of SCLK clocks in one data bit from the SDIN pin. A rising edge on CSB latches in a complete control word consisting of the last 16 bits.
latch CSB
SCLK
SDIN
B15
B14
B13
B12
B11
B10
B9
B8
B7
B6
B5
B4
B3
B2
B1
B0
control register address
control register data bits
Figure 19 3-Wire Serial Control Interface
2-WIRE SERIAL CONTROL MODE
The WM8750L supports software control via a 2-wire serial bus. Many devices can be controlled by the same bus, and each device has a unique 7-bit address (this is not the same as the 7-bit address of each register in the WM8750L). The WM8750L operates as a slave device only. The controller indicates the start of data transfer with a high to low transition on SDIN while SCLK remains high. This indicates that a device address and data will follow. All devices on the 2-wire bus respond to the start condition and shift in the next eight bits on SDIN (7-bit address + Read/Write bit, MSB first). If the device address received matches the address of the WM8750L and the R/W bit is `0', indicating a write, then the WM8750L responds by pulling SDIN low on the next clock pulse (ACK). If the address is not recognised or the R/W bit is `1', the WM8750L returns to the idle condition and wait for a new start condition and valid address. Once the WM8750L has acknowledged a correct address, the controller sends the first byte of control data (B15 to B8, i.e. the WM8750L register address plus the first bit of register data). The WM8750L then acknowledges the first data byte by pulling SDIN low for one clock pulse. The controller then sends the second byte of control data (B7 to B0, i.e. the remaining 8 bits of register data), and the WM8750L acknowledges again by pulling SDIN low. The transfer of data is complete when there is a low to high transition on SDIN while SCLK is high. After receiving a complete address and data sequence the WM8750L returns to the idle state and waits for another start condition. If a start or stop condition is detected out of sequence at any point during data transfer (i.e. SDIN changes while SCLK is high), the device jumps to the idle condition.
SDIN
DEVICE ADDRESS (7 BITS)
RD / WR BIT
ACK (LOW)
CONTROL BYTE 1 (BITS 15 TO 8)
ACK (LOW)
CONTROL BYTE 2 (BITS 7 TO 0)
ACK (LOW)
SCLK
START
register address and 1st register data bit
remaining 8 bits of register data
STOP
Figure 20 2-Wire Serial Control Interface
PP Rev 1.77 May 2003 42
Product Preview
WM8750L
The WM8750L has two possible device addresses, which can be selected using the CSB pin. CSB STATE Low High DEVICE ADDRESS 0011010 (0 x 34h) 0011011 (0 x 36h)
Table 39 2-Wire MPU Interface Address Selection
POWER SUPPLIES
The WM8750L can use up to four separate power supplies: * AVDD / AGND: Analogue supply, powers all analogue functions except the headphone drivers. AVDD can range from 1.8V to 3.6V and has the most significant impact on overall power consumption (except for power consumed in the headphone). A large AVDD slightly improves audio quality. HPVDD / HPGND: Headphone supply, powers the headphone drivers. HPVDD can range from 1.8V to 3.6V. HPVDD is normally tied to AVDD, but it requires separate layout and decoupling capacitors to curb harmonic distortion. With a larger HPVDD, louder headphone and speaker outputs can be achieved with lower distortion. If HPVDD is lower than AVDD, the output signal may be clipped. DCVDD: Digital core supply, powers all digital functions except the audio and control interfaces. DCVDD can range from 1.42V to 3.6V, and has no effect on audio quality. The return path for DCVDD is DGND, which is shared with DBVDD. DBVDD: Digital buffer supply, powers the audio and control interface buffers. This makes it possible to run the digital core at very low voltages, saving power, while interfacing to other digital devices using a higher voltage. DBVDD draws much less power than DCVDD, and has no effect on audio quality. DBVDD can range from 1.8V to 3.6V. The return path for DBVDD is DGND, which is shared with DCVDD.
*
*
*
It is possible to use the same supply voltage on all four. However, digital and analogue supplies should be routed and decoupled separately to keep digital switching noise out of the analogue signal paths.
PP Rev 1.77 May 2003 43
WM8750L
POWER MANAGEMENT
Product Preview
The WM8750L has two control registers that allow users to select which functions are active. For minimum power consumption, unused functions should be disabled. To avoid any pop or click noise, it is important to enable or disable functions in the correct order (see Applications Information). VMIDSEL is the enable for the Vmid reference, which defaults to disabled and can be enabled as a 50kOhm potential divider or, for low power maintenance of Vref when all other blocks are disabled, as a 500kOhm potential divider.
REGISTER ADDRESS R25 (19h) Power Manageme nt (1)
BIT 8:7
LABEL VMIDSEL
DEFAULT 00
DESCRIPTION Vmid divider enable and select 00 - Vmid disabled (for OFF mode) 01 - 50kOhm divider enabled (for playback/record) 10 - 500kOhm divider enabled (for low-power standby) 11 - 5kOhm divider enabled (for fast start-up) VREF (necessary for all other functions) Analogue in PGA Left Analogue in PGA Right ADC Left ADC Right MICBIAS DAC Left DAC Right LOUT1 Output Buffer* ROUT1 Output Buffer* LOUT2 Output Buffer* ROUT2 Output Buffer* MONOOUT Output Buffer and Mono Mixer OUT3 Output Buffer
6 5 4 3 2 1 R26 (1Ah) Power Manageme nt (2) 8 7 6 5 4 3 2 1
VREF AINL AINR ADCL ADCR MICB DACL DACR LOUT1 ROUT1 LOUT2 ROUT2 MONO OUT3
0 0 0 0 0 0 0 0 0 0 0 0 0 0
Note: All control bits are 0=OFF, 1=ON * The left mixer is enabled when LOUT1=1 or LOUT2=1. The right mixer is enabled when ROUT1=1 or ROUT2=1. Table 40 Power Management
STOPPING THE MASTER CLOCK
In order to minimise power consumed in the digital core of the WM8750L, the master clock should be stopped in Standby and OFF modes. If this is cannot be done externally at the clock source, the DIGENB bit (R25, bit 0) can be set to stop the MCLK signal from propagating into the device core. In Standby mode with all supplies at 3.3V, setting DIGENB saves approximately 0.27mA on DCVDD and 0.2mA on DBVDD. However, since setting DIGENB has no effect on the power consumption of other system components external to the WM8750L, it is preferable to disable the master clock at its source wherever possible. REGISTER ADDRESS R25 (19h) Additional Control (1) 1 BIT LABEL DIGENB 0 DEFAULT DESCRIPTION Master clock disable 0: master clock enabled 1: master clock disabled
Table 41 ADC and DAC Oversampling Rate Selection NOTE: Before DIGENB can be set, the control bits ADCL, ADCR, DACL and DACR must be set to zero and a waiting time of 1ms must be observed. Any failure to follow this procedure may prevent DACs and ADCs from re-starting correctly.
PP Rev 1.77 May 2003 44
Product Preview
WM8750L
SAVING POWER BY REDUCING OVERSAMPLING RATE
The default mode of operation of the ADC and DAC digital filters is in 128x oversampling mode. Under the control of ADCOSR and DACOSR the oversampling rate may be halved. This will result in a slight decrease in noise performance but will also reduce the power consumption of the device. REGISTER ADDRESS R24 (18h) Additional Control (2) 1 BIT LABEL ADCOSR 0 DEFAULT DESCRIPTION ADC oversample rate select 1 = 64x (lowest power) 0 = 128x (best SNR) DAC oversample rate select 1 = 64x (lowest power) 0 = 128x (best SNR)
0
DACOSR
0
Table 42 ADC and DAC Oversampling Rate Selection
SAVING POWER AT LOW SUPPLY VOLTAGES
The analogue supplies to the WM8750L can run from 1.8V to 3.6V. By default, all analogue circuitry on the device is optimized to run at 3.3V. This set-up is also good for all other supply voltages down to 1.8V. However, at lower voltages, it is possible to save power by reducing the internal bias currents used in the analogue circuitry. This is controlled as shown below. REGISTER ADDRESS R23 (17h) Additional Control(1) BIT 7:6 LABEL VSEL [1:0] DEFAULT 11 DESCRIPTION Analogue Bias optimization 00: Lowest bias current, optimized for AVDD=1.8V 01: Low bias current, optimized for AVDD=2.5V 1X: Default bias current, optimized for AVDD=3.3V
PP Rev 1.77 May 2003 45
WM8750L REGISTER MAP
ADDRESS REGISTER (Bit 15 - 9) R0 (00h) R1 (01h) R2 (02h) R3 (03h) R4 (04h) R5 (05h) R6 (06h) R7 (07h) R8 (08h) R9 (09h) R10 (0Ah) R11 (0Bh) R12 (0Ch) R13 (0Dh) R15 (0Fh) R16 (10h) R17 (11h) R18 (12h) R19 (13h) R20 (14h) R21 (15h) R22 (16h) R23 (17h) R24 (18h) R25 (19h) R26 (1Ah) R27 (1Bh) R31 (1Fh) R32 (20h) R33 (21h) R34 (22h) R35 (23h) R36 (24h) R37 (25h) R38 (26h) R39 (27h) R40 (28h) R41 (29h) R42 (2Ah) 0000000 0000001 0000010 0000011 0000100 0000101 0000110 0000111 0001000 0001001 0001010 0001011 0001100 0001101 0001111 0010000 0010001 0010010 0010011 0010100 0010101 0010110 0010111 0011000 0011001 0011010 0011011 0011111 0100000 0100001 0100010 0100011 0100100 0100101 0100110 0100111 0101000 0101001 0101010 Left Input volume Right Input volume LOUT1 volume ROUT1 volume Reserved ADC & DAC Control Reserved Audio Interface Sample rate Reserved Left DAC volume Right DAC volume Bass control Treble control Reset 3D control ALC1 ALC2 ALC3 Noise Gate Left ADC volume Right ADC volume Additional control(1) Additional control(2) Pwr Mgmt (1) Pwr Mgmt (2) Additional Control (3) ADC input mode ADCL signal path ADCR signal path Left out Mix (1) Left out Mix (2) Right out Mix (1) Right out Mix (2) Mono out Mix (1) Mono out Mix (2) LOUT2 volume ROUT2 volume MONOOUT volume 0 LIVU RIVU LO1VU RO1VU 0 LINMUTE RINMUTE LO1ZC RO1ZC 0 0 0 0 HPOR 0 LRP LIZC RIZC LINVOL RINVOL LOUT1VOL[6:0] ROUT1VOL[6:0] 0 DACMU 0 WL[1:0] SR[4:0] 0 0 0 0 0 0 0 0 ADCHPD 0 remarks Bit[8] Bit[7] Bit[6] Bit[5] Bit[4] Bit[3] Bit[2] Bit[1] Bit[0]
Product Preview
default 010010111 010010111 001111001 001111001 000000000 000001000 000000000 000001010 000000000 000000000 011111111 011111111
page ref 19 19 31 31 19,25,28 39 40 26 26 27 27 25 23 23 23 24 21 21 18,19,28,35 32, 34,45 44 44 35 17 17 17 29 29 30 30 30 30 32 32 32
ADCDIV2 DACDIV2 0 0 0 0 LDVU RDVU 0 0 BB 0 0 BCLKINV 0 0
ADCPOL[1:0] 0 MS CLKDIV2 0 0 LRSWAP
DEEMPH[1:0] 0 0
FORMAT[1:0] USB 0
LDACVOL[7:0] RDACVOL[7:0] BC TC 0 0 0 0 BASS[3:0] TRBL[3:0]
000001111 000001111 not reset 3DEN 000000000 001111011 000000000 000110010 NGAT 000000000 011000011 011000011
writing to this register resets all registers to their default state MODE3D 3DUC 3DLC MAXGAIN[2:0] 0 DCY[3:0] NGTH[4:0] LADCVOL[7:0] RADCVOL[7:0] VSEL[1:0] DMONOMIX[1:0] DATSEL[1:0] TRI ADCL ROUT2 0 0 0 0 0 0 0 0 0 0 LOUT2VOL[6:0] ROUT2VOL[6:0] MOUTVOL[6:0] 0 0 0 0 LRCM ADCR MONO 0 0 0 0 DACINV ADCOSR MICB OUT3 0 0 0 0 LMIXSEL[2:0] 0 RMIXSEL[2:0] 0 0 0 0 0 0 0 TOEN DACOSR DIGENB 0 0 0 0 0 0 0 3DDEPTH[3:0] ALCL[3:0] HLD[3:0] ATK[3:0] NGG[1:0]
ALCSEL[1:0] 0 0 0 LAVU RAVU TSDEN ALCZC
011000000 000000000 000000000 000000000 000000000 000000000 000000000 000000000 001010000 001010000 001010000 001010000 001010000 001010000 001111001 001111001 001111001
OUT3SW[1:0] VMIDSEL[1:0] DACL DACR
HPSWEN HPSWPOL ROUT2INV VREF LOUT1 VROI AINL ROUT1 0 RDCM AINR LOUT2 0 LDCM
ADCLRM[1:0] DS 0 0 LD2LO RD2LO LD2RO RD2RO LD2MO RD2MO LO2VU RO2VU 0
MONOMIX[1:0] LINSEL[1:0] RINSEL[1:0] LI2LO RI2LO LI2RO RI2RO LI2MO RI2MO LO2ZC RO2ZC MOZC
LMICBOOST[1:0] RMICBOOST[1:0] LI2LOVOL[2:0] RI2LOVOL[2:0] LI2ROVOL[2:0] RI2ROVOL[2:0] LI2MOVOL[2:0] RI2MOVOL[2:0]
PP Rev 1.77 May 2003 46
Product Preview
WM8750L
DIGITAL FILTER CHARACTERISTICS
The ADC and DAC employ different digital filters. There are 4 types of digital filter, called Type 0, 1, 2 and 3. The performance of Types 0 and 1 is listed in the table below, the responses of all filters is shown in the proceeding pages.
PARAMETER Passband Passband Ripple Stopband Stopband Attenuation Passband Passband Ripple Stopband Stopband Attenuation High Pass Filter Corner Frequency
TEST CONDITIONS +/- 0.05dB -6dB
MIN 0
TYP
MAX 0.416fs
UNIT
ADC Filter Type 0 (USB Mode, 250fs operation) 0.5fs +/- 0.05 0.584fs f > 0.584fs +/- 0.05dB -6dB 0.5465fs f > 0.5465fs -3dB -0.5dB -0.1dB DAC Filter Type 0 (USB mode, 250fs operation) Passband Passband Ripple Stopband Stopband Attenuation Passband Passband Ripple Stopband Stopband Attenuation Table 44 Digital Filter Characteristics f > 0.5465fs 0.5465fs -50 dB f > 0.584fs +/- 0.03dB -6dB 0.584fs -50 0 0.5fs +/- 0.03 dB 0.4535fs dB +/- 0.03dB -6dB 0 0.5fs +/-0.03 dB 0.416fs -60 3.7 10.4 21.6 dB Hz -60 0 0.5fs +/- 0.05 dB 0.4535fs dB dB
ADC Filter Type 1 (USB mode, 272fs or Normal mode operation)
DAC Filter Type 1 (USB mode, 272fs or Normal mode operation)
TERMINOLOGY
1. 2. Stop Band Attenuation (dB) - the degree to which the frequency spectrum is attenuated (outside audio band) Pass-band Ripple - any variation of the frequency response in the pass-band region
PP Rev 1.77 May 2003 47
WM8750L DAC FILTER RESPONSES
0.02
0
Product Preview
0.01
-20
0
Response (dB)
-40
Response (dB)
0 0.5 1 1.5 Frequency (Fs) 2 2.5 3
-0.01 -0.02 -0.03 -0.04 -0.05
-60
-80
-100
-0.06 0 0.05 0.1 0.15 0.2 0.25 0.3 Frequency (Fs) 0.35 0.4 0.45 0.5
Figure 21 DAC Digital Filter Frequency Response - Type 0 Figure 22 DAC Digital Filter Ripple - Type 0
0.02
0
0.01
-20
0
Response (dB)
-40
Response (dB)
-0.01 -0.02 -0.03 -0.04
-60
-80
-0.05
-100 0 0.5 1 1.5 Frequency (Fs) 2 2.5 3
-0.06 0 0.05 0.1 0.15 0.2 0.25 0.3 Frequency (Fs) 0.35 0.4 0.45 0.5
Figure 23 DAC Digital Filter Frequency Response - Type 1 Figure 24 DAC Digital Filter Ripple - Type 1
0.02
0
0.01
-20
0
Response (dB)
-40
Response (dB)
-0.01 -0.02 -0.03 -0.04
-60
-80
-0.05
-100 0 0.5 1 1.5 Frequency (Fs) 2 2.5 3
-0.06 0 0.05 0.1 0.15 Frequency (Fs) 0.2 0.25
Figure 25 DAC Digital Filter Frequency Response - Type 2 Figure 26 DAC Digital Filter Ripple - Type 2
PP Rev 1.77 May 2003 48
Product Preview
0.25
0
WM8750L
0.2
-20
0.15 0.1
Response (dB)
Response (dB)
-40
0.05 0 -0.05 -0.1
-60
-80
-0.15 -0.2
-100 0 0.5 1 1.5 Frequency (Fs) 2 2.5 3
-0.25 0 0.05 0.1 0.15 Frequency (Fs) 0.2 0.25
Figure 27 DAC Digital Filter Frequency Response - Type 3 Figure 28 DAC Digital Filter Ripple - Type 3
ADC FILTER RESPONSES
0.04
0
0.03
-20
0.02
Response (dB)
-40
Response (dB)
0.01 0 -0.01 -0.02
-60
-80
-0.03
-100 0 0.5 1 1.5 Frequency (Fs) 2 2.5 3
-0.04 0 0.05 0.1 0.15 0.2 0.25 0.3 Frequency (Fs) 0.35 0.4 0.45 0.5
Figure 29 ADC Digital Filter Frequency Response - Type 0
0
Figure 30 ADC Digital Filter Ripple - Type 0
0.02 0.01
-20
0
Response (dB)
-40
Response (dB)
-0.01 -0.02 -0.03 -0.04
-60
-80
-0.05
-100 0 0.5 1 1.5 Frequency (Fs) 2 2.5 3
-0.06 0 0.05 0.1 0.15 0.2 0.25 0.3 Frequency (Fs) 0.35 0.4 0.45 0.5
Figure 31 ADC Digital Filter Frequency Response - Type 1
Figure 32 ADC Digital Filter Ripple - Type 1
PP Rev 1.77 May 2003 49
WM8750L
0.25
0
Product Preview
0.2
-20
0.15 0.1
Response (dB)
Response (dB)
-40
0.05 0 -0.05 -0.1
-60
-80
-0.15 -0.2
-100 0 0.5 1 1.5 Frequency (Fs) 2 2.5 3
-0.25 0 0.05 0.1 0.15 Frequency (Fs) 0.2 0.25
Figure 33 ADC Digital Filter Frequency Response - Type 2
Figure 34 ADC Digital Filter Ripple - Type 2
0.25
0
0.2 0.15
-20
0.1
Response (dB)
Response (dB)
-40
0.05 0 -0.05 -0.1
-60
-80
-0.15 -0.2
-100 0 0.5 1 1.5 Frequency (Fs) 2 2.5 3
-0.25 0 0.05 0.1 0.15 Frequency (Fs) 0.2 0.25
Figure 35 ADC Digital Filter Frequency Response - Type 2
Figure 36 ADC Digital Filter Ripple - Type 3
DE-EMPHASIS FILTER RESPONSES
0
0.4 0.3
-2
0.2
Response (dB)
-4
Response (dB)
0.1 0 -0.1 -0.2
-6
-8
-0.3
-10 0 2000 4000 6000 8000 10000 Frequency (Fs) 12000 14000 16000
-0.4 0 2000 4000 6000 8000 10000 Frequency (Fs) 12000 14000 16000
Figure 37 De-emphasis Frequency Response (32kHz)
Figure 38 De-emphasis Error (32kHz)
PP Rev 1.77 May 2003 50
Product Preview
0
0.4 0.3
WM8750L
-2
0.2
Response (dB)
Response (dB)
-4
0.1 0 -0.1 -0.2
-6
-8
-0.3 -0.4
-10 0 5000 10000 Frequency (Fs) 15000 20000
0
5000
10000 Frequency (Fs)
15000
20000
Figure 39 De-emphasis Frequency Response (44.1kHz)
0
Figure 40 De-emphasis Error (44.1kHz)
0.4 0.3
-2
0.2
Response (dB)
Response (dB)
-4
0.1 0 -0.1 -0.2
-6
-8
-0.3 -0.4
-10 0 5000 10000 Frequency (Fs) 15000 20000
0
5000
10000 Frequency (Fs)
15000
20000
Figure 41 De-emphasis Frequency Response (48kHz)
Figure 42 De-emphasis Error (48kHz)
HIGHPASS FILTER
The WM8750L has a selectable digital highpass filter in the ADC filter path to remove DC offsets. The filter response is characterised by the following polynomial:
H(z) =
1 - z-1 1 - 0.9995z-1
0
Response (dB)
-5
-10
-15
Figure 43 ADC Highpass Filter Response
0 0.0005 0.001 Frequency (Fs) 0.0015 0.002
PP Rev 1.77 May 2003 51
WM8750L APPLICATIONS INFORMATION
RECOMMENDED EXTERNAL COMPONENTS
Product Preview
DVDD
AVDD 3 2 18 17 DBVDD DCVDD AVDD HPVDD
DGND
4 DGND
HPGND AGND
14 19 AGND
C1 C2
C3
C4
DGND
AGND 1 MCLK BCLK ADCLRC DACLRC DACDAT ADCDAT
LOUT2
16
+
ROUT2
15
8 OHM LOUDSPEAKER
+ C13
AUDIO INTERFACE (I2S/LJ/RJ/DSP)
5 9 7 6 8
MONOOUT
10
OUT3
11
32 OHM EAR SPEAKER
+ C14 + C15
HIGH for 3-wire LOW for 2-wire CONTROL INTERFACE (2 OR 3-WIRE)
C7 C8 C9
29
LOUT1 MODE ROUT1
13 12
30 31 32
CSB SDIN SCLK
WM8750L
MICBIAS VREF VMID 22 20
16 OR 32 OHM HEADPHONES
28 27 26 25 24 23
LINPUT1 RINPUT1 LINPUT2 RINPUT2
AVDD + C5
DVDD + C6
C18
+ C19
C20
21
C16
+ C21
+ C17 AGND
C10 C11
LINPUT3 RINPUT3 / HPDETECT
AGND
DGND
AGND See External Components Descriptions for details
C12
Layout Notes: 1. C1 to C4, C16, C18 and C20 should be as close to the relative WM8750L connecting pin as possible. 2. AGND and DGND should be joined as close to the WM8750L as possible.
Recommended External Components Diagram
PP Rev 1.77 May 2003 52
Product Preview
WM8750L
SUGGESTED VALUE 100nF 10uF 1uF 2.2uF 220uF 100nF 10uF 100nF 10uF 100nF 10uF DESCRIPTION De-coupling for DBVDD, DCVDD, AVDD, HPVDD Reservoir capacitor for DVDD, AVDD. Should the supplies use separate sources then additional capacitors will be required of each additional source. AC input coupling capacitors Output AC coupling capacitors to remove DC level from MONOOUT Output AC coupling capacitors to remove DC level from headphone output (If used as a line-out only, use 2.2uF caps. In capless mode using OUT3 , no caps are needed) De-coupling for VMID. Reservoir capacitor for VMID De-coupling for VREF Reservoir capacitor for VREF De-coupling for MICBIAS - Not required if MICBIAS output is not used Reservoir capacitor for MICBIAS - Not required if MICBIAS output is not used
COMPONENT REFERENCE C1 - C4 C5 - C6 C7 - C12 C13 C14 & C15 C16 C17 C18 C19 C20 C21
External Components Descriptions Note: 2 For Capacitors C5, C6, C17, C19 and C21 it is recommended that very low ESR components are used.
LINE INPUT CONFIGURATION
When LINPUT1/RINPUT1 or LINPUT2/RINPUT2 are used as line inputs, the microphone boost and ALC functions should normally be disabled. In order to avoid clipping, the user must ensure that the input signal does not exceed AVDD. This may require a potential divider circuit in some applications. It is also recommended to remove RF interference picked up on any cables using a simple first-order RC filter, as high-frequency components in the input signal may otherwise cause aliasing distortion in the audio band. AC signals with no DC bias should be fed to the WM8750L through a DC blocking capacitor, e.g. 1F.
MICROPHONE INPUT CONFIGURATION
MICBIAS R1 680 Ohm to 2.2kOhm check microphone's specification LINPUT1/2/3 RINPUT1/2/3
FROM MICROPHONE
C2 1uF AGND R2 47kOhm C1 220pF
AGND
AGND
Figure 44 Recommended Circuit for Line Input For interfacing to a microphone, the ALC function should be enabled and the microphone boost switched on. Microphones held close to a speaker's mouth would normally use the 13dB gain setting, while tabletop or room microphones would need a 29dB boost. The recommended application circuit is shown above. R1 and R2 form part of the biasing network (refer to Microphone Bias section). R1 connected to MICBIAS is necessary only for electret type microphones that require a voltage bias. R2 should always be present to prevent the microphone input from charging to a high voltage which may damage the microphone on connection. R1 and R2 PP Rev 1.77 May 2003 53
WM8750L
Product Preview should be large so as not to attenuate the signal from the microphone, which can have source impedance greater than 2kOhm. C1 together with the source impedance of the microphone and the WM8750L input impedance forms an RF filter. C2 is a DC blocking capacitor to allow the microphone to be biased at a different DC voltage to the MICIN signal.
MINIMISING POP NOISE AT THE ANALOGUE OUTPUTS
To minimise any pop or click noise when the system is powered up or down, the following procedures are recommended.
POWER UP
* Switch on power supplies. By default the WM8750L is in Standby Mode, the DAC is digitally muted and the Audio Interface, Line outputs and Headphone outputs are all OFF (DACMU = 1 Power Management registers 1 and 2 are all zeros). Enable Vmid and VREF, then wait for time TBD Enable DACs as required Enable line and / or headphone output buffers as required. Set DACMU = 0 to soft-un-mute the audio DACs. Set DACMU = 1 to soft-mute the audio DACs. Disable all output buffers, then wait for time TBD. Switch off the power supplies.
* * * * * * *
POWER DOWN
POWER MANAGEMENT EXAMPLES
OPERATION MODE
VR
POWER MANAGEMENT (1) PGAs
AI
POWER MANAGEMENT (2) DACs
MBI DAL DAR LO1
ADCs
ADR
Output Buffers
RO1 LO2 RO2 MO HPD
PGL PGR ADL
Stereo Headphone Playback Stereo Line-in Record Stereo Microphone Record Mono Microphone Record Stereo Line-in to Headphone Out Phone Call Speaker Phone Call [ROUT2INV = 1] Record Phone Call [L channel = mic with boost, R channel = RX, enable mono mix]
1 1 1 1 1 1 1 1
1 1 1 1 1 1 1 1
0 1 1 1 0 1 1 1
0 1 1 0 0 0 0 1
0 1 1 1 0 0 0 1
0 1 1 0 0 0 0 1
0 0 1 1 0 1 1 1
1 0 0 0 0 0 0 0
1 0 0 0 0 0 0 0
1 0 0 0 1 1 0 1
1 0 0 0 1 1 0 1
0 0 0 0 0 0 1 0
0 0 0 0 0 0 1 0
0 0 0 0 0 1 1 1
x 0 0 0 x x 0 x
PP Rev 1.77 May 2003 54
Product Preview
WM8750L
PACKAGE DIMENSIONS
FL: 32 PIN QFN PLASTIC PACKAGE 5 X 5 X 0.9 mm BODY, 0.50 mm LEAD PITCH DM030.C
CORNER TIE BAR 5 25
D2 B D2/2 32
SEE DETAIL A
D
L 24 1 INDEX AREA (D/2 X E/2) E2/2
A
E2
SEE DETAIL B
E
17
8 2X 16 e 15 B 9 b 2X aaa C aaa C
TOP VIEW
ccc C (A3) 1 A 0.08 C A1 SEATING PLANE 1 e/2 TERMINAL TIP L 1
DETAIL A
32x b bbb M C A B
CORNER TIE BAR 5
C
43 0.
DETAIL B
DATUM
m m 6 56 0.
32x K
m m
EXPOSED CENTRE PAD
R
e
1 L1 L1 R
Symbols A A1 A3 b D D2 E E2 e L L1 R K aaa bbb ccc REF: MIN 0.85 0 0.18 4.90 3.2 4.90 3.2 0.35
1 b(min)/2 0.20 Tolerances of Form and Position 0.15 0.10 0.10 JEDEC, MO-220, VARIATION VKKD-2
Dimensions (mm) NOM MAX 0.90 1.00 0.02 0.05 0.2 REF 0.23 0.30 5.00 5.10 3.3 3.4 5.00 5.10 3.3 3.4 0.5 BSC 0.4 0.45 0.1
NOTE
1 2 2
NOTES: 1. DIMENSION b APPLIED TO METALLIZED TERMINAL AND IS MEASURED BETWEEN 0.25 mm AND 0.30 mm FROM TERMINAL TIP. DIMENSION L1 REPRESENTS TERMINAL PULL BACK FROM PACKAGE SIDE WALL. MAXIMUM OF 0.1mm IS ACCEPTABLE. WHERE TERMINAL PULL BACK EXISTS, ONLY UPPER HALF OF LEAD IS VISIBLE ON PACKAGE SIDE WALL DUE TO HALF ETCHING OF LEADFRAME. 2. FALLS WITHIN JEDEC, MO-220 WITH THE EXCEPTION OF D2, E2: D2,E2: LARGER PAD SIZE CHOSEN WHICH IS JUST OUTSIDE JEDEC SPECIFICATION 3. ALL DIMENSIONS ARE IN MILLIMETRES 4. THIS DRAWING IS SUBJECT TO CHANGE WITHOUT NOTICE. 5. SHAPE AND SIZE OF CORNER TIE BAR MAY VARY WITH PACKAGE TERMINAL COUNT. CORNER TIE BAR IS CONNECTED TO EXPOSED PAD INTERNALLY
PP Rev 1.77 May 2003 55
WM8750L IMPORTANT NOTICE
Product Preview
Wolfson Microelectronics plc (WM) reserve the right to make changes to their products or to discontinue any product or service without notice, and advise customers to obtain the latest version of relevant information to verify, before placing orders, that information being relied on is current. All products are sold subject to the WM terms and conditions of sale supplied at the time of order acknowledgement, including those pertaining to warranty, patent infringement, and limitation of liability. WM warrants performance of its products to the specifications applicable at the time of sale in accordance with WM's standard warranty. Testing and other quality control techniques are utilised to the extent WM deems necessary to support this warranty. Specific testing of all parameters of each device is not necessarily performed, except those mandated by government requirements. In order to minimise risks associated with customer applications, adequate design and operating safeguards must be used by the customer to minimise inherent or procedural hazards. WM assumes no liability for applications assistance or customer product design. WM does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or other intellectual property right of WM covering or relating to any combination, machine, or process in which such products or services might be or are used. WM's publication of information regarding any third party's products or services does not constitute WM's approval, license, warranty or endorsement thereof. Reproduction of information from the WM web site or datasheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations and notices. Representation or reproduction of this information with alteration voids all warranties provided for an associated WM product or service, is an unfair and deceptive business practice, and WM is not responsible nor liable for any such use. Resale of WM's products or services with statements different from or beyond the parameters stated by WM for that product or service voids all express and any implied warranties for the associated WM product or service, is an unfair and deceptive business practice, and WM is not responsible nor liable for any such use.
ADDRESS:
Wolfson Microelectronics plc 20 Bernard Terrace Edinburgh EH8 9NX United Kingdom Tel :: +44 (0)131 272 7000 Fax :: +44 (0)131 272 7001 Email :: sales@wolfsonmicro.com
PP Rev 1.77 May 2003 56

▲Up To Search▲

Price & Availability of WM8750LEFLR

	To Download WM8750LEFLR Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .